Rescued a P code SSP!!

[MagnoliaTom]

Picked up an SSP this morning off CL. It was listed for $50 but I got it for $30. Had to drive 6 hour round trip to get it but that's what you gotta do sometimes.

I want to give thanks to @Walchit for fielding all my newbie questions.

The bowl is in kinda rough shape. The rest is not bad. No ash catcher or one touch but doubt I could make it work with the rust.

Would like suggestions on what to do about the bowl....leave it and start cooking. Get cheap donor bowl in black and drill holes to mount everything?

Need to fix the side bars. Seller gave some 1" square tubing to replace the rusted originals.

I gave it a quick washing and cleaning and it looks pretty nice!


The CL listing


Loaded up




Before pics





Think I may just cook some burgers on it as is tonight just to see how it cooks.


Sent from my iPhone using Tapatalk

[JEBIV]

You nailed the rescue and respect you have some work on the restore, check with the club over on member sales and trades and see if you can get some parts you may need

[MagnoliaTom]

You nailed the rescue and respect you have some work on the restore, check with the club over on member sales and trades and see if you can get some parts you may need

Thank you! I appreciate the kind words and sage advice.


Sent from my iPhone using Tapatalk

[Walchit]

Ive been sitting here worried the lid blew out! Glad you got it home. Its about as rough as I expected, but that lid looks great. It will cook as-is, but you won't get the full experience of the weber without being able to control your air flow.

I used star nuts from the bicycle shop, I had to use 1 and 1/8 inch ones, and used a grinder to make them somewhat square. Then screwed the bolt in a little and tapped it in slowly and tried to keep it straight. You can just tap the side of the bolt to straighten it out if it starts getting out of control. Went pretty easy for me but I may have gotten lucky.

I know @red5wrangler used stainless all thread through the pipe, with washers that are the size of the inside diameter of the tubing to keep it lined up. I probably would have done that, but I already sourced the star nuts and it worked well, but I haven't found stainless bolts in the metric thread that are long enough.

[MagnoliaTom]

Ive been sitting here worried the lid blew out! Glad you got it home. Its about as rough as I expected, but that lid looks great. It will cook as-is, but you won't get the full experience of the weber without being able to control your air flow.

I used star nuts from the bicycle shop, I had to use 1 and 1/8 inch ones, and used a grinder to make them somewhat square. Then screwed the bolt in a little and tapped it in slowly and tried to keep it straight. You can just tap the side of the bolt to straighten it out if it starts getting out of control. Went pretty easy for me but I may have gotten lucky.

I know @red5wrangler used stainless all thread through the pipe, with washers that are the size of the inside diameter of the tubing to keep it lined up. I probably would have done that, but I already sourced the star nuts and it worked well, but I haven't found stainless bolts in the metric thread that are long enough.

I had it tied down before I left

What do you think about these brackets I salvaged off an old fence? I already painted the tubing.



I know it's not factory correct but it would work and be very easy to install with self tapping screws.


Sent from my iPhone using Tapatalk

[Walchit]

I would probably try one of the other ways, are they the right length?

[MagnoliaTom]

The tubing he gave me needs to be cut to the right size.


Sent from my iPhone using Tapatalk

[Walchit]

Do the brackets slide in the end of the pipe? They would work for sure, but you would be putting some extra holes in it. I guess I would let the budget decide. Idk how much the all tread costs, but the star nuts were about 4 bucks a piece.

[MagnoliaTom]

Yes the brackets slide into the tubing. I could get the all thread but wondering how to keep the tubing in place and not spin once in place



Sent from my iPhone using Tapatalk

[MagnoliaTom]

Giving the new grill a test run




Sent from my iPhone using Tapatalk

[Walchit]

I think if you get it pretty tight with the all thread, then line the bar up how you want it you should be able to tighten it and that would hold it. Might need a buddy to hold the other side

[ReanimatedRobot]

I wish you luck man.  I can't believe that bowl is rusted out so badly for no older than it is.  I brought home a second Gen that they used as a garbage burner and it looks pretty super compared to that.  If you have any friends who weld or have metal working tools now is the time to call in those favors if parts can't be sourced.  I am sure you will manage either way!

[smokeyjoe]

I have a green one touch platinum just as bad as that one, still cooks tho so good enough for me.


Sent from my iPhone using Weber Kettle Club

[MagnoliaTom]

Worked on the lower frame support.
Had to cut the tubes to length


Added caps that I drilled holes thru the center


Used some 36" long, 1/4 all thread that was the perfect length


Used SS acorn nuts on both ends with washers


Cart is nice and sturdy now





Sent from my iPhone using Tapatalk

[Walchit]

Those end caps were a good idea! Looks just like new! Now its ready to stay in the flock right?