Welcome,
Guest
Login
or
Register
Slow N Sear
Age Guide
WKC Merch
Grill Gallery
Forum
Login
Register
Shop Amazon.com and support the WKC
|
WKC T-Shirts
Weber Kettle Club Forums
»
Cooking & Food Talk
»
Charcoal Grilling & BBQ
(Moderators:
SixZeroFour
,
Cellar2ful
) »
Ry and his Dremel cut
« previous
next »
Print
Pages: [
1
]
Author
Topic: Ry and his Dremel cut (Read 2338 times)
hansonb4
Smokey Joe
Posts: 82
Ry and his Dremel cut
«
on:
August 02, 2020, 06:02:26 AM »
Has anyone had a problem with the kettle lid crimping / damaging their probe leads? I saw that Ry made the cut in the side of their grill to feed the lines and I don't want to run then through the vent on the lid.
Thanks,
Bob / hansonb4
Sent from my Pixel 3 using
Weber Kettle Club mobile app
Logged
HoosierKettle
WKC Ambassador
Posts: 7366
Re: Ry and his Dremel cut
«
Reply #1 on:
August 02, 2020, 06:48:37 AM »
I would not notch the top of the bowl. That rolled steel lip is part of the structural integrity of the bowl.
Sent from my iPhone using
Weber Kettle Club mobile app
Logged
HoosierKettle
WKC Ambassador
Posts: 7366
Re: Ry and his Dremel cut
«
Reply #2 on:
August 02, 2020, 06:50:33 AM »
I just run my wires between bowl and lid and haven’t ruined a probe yet. Drill a hole for a probe port would be a better option then notching
Sent from my iPhone using
Weber Kettle Club mobile app
Logged
foshizzle
WKC Brave
Posts: 468
Re: Ry and his Dremel cut
«
Reply #3 on:
August 02, 2020, 11:36:39 AM »
I notched an 18” and although it made things a little easier for wire management then using the grommet I ended up selling it and going back to an un-notched 18” and just putting the wires under the lid. Have done that with the Maverick Et732 and Flame Boss probes crimped under the lid with no problems.
Sent from my iPhone using
Weber Kettle Club mobile app
Logged
SMOKE FREAK
WKC Ranger
Posts: 1115
Re: Ry and his Dremel cut
«
Reply #4 on:
August 02, 2020, 05:11:36 PM »
I made a notch in my stick burner but the lid on that thing is at least 20 pounds. I wouldn't think the lid on a kettle would be a problem.
That said...I don't use probes/therms in my kettle...
Logged
bamakettles
WKC Ambassador
Posts: 6063
Re: Ry and his Dremel cut
«
Reply #5 on:
August 02, 2020, 06:26:05 PM »
I would not notch. I’ve drilled one kettle that was not a looker - strictly a cooker and installed a cable gland. It works well for cooks requiring thermometer probes.
Sent from my iPad using
Weber Kettle Club
Logged
Darko
WKC Performer
Posts: 4855
Re: Ry and his Dremel cut
«
Reply #6 on:
August 04, 2020, 08:52:01 AM »
I've never had an issue with the wires getting crimped as long as you dont slam the lid down.
Logged
Mike in Roseville
WKC Performer
Posts: 2261
Re: Ry and his Dremel cut
«
Reply #7 on:
August 04, 2020, 09:11:47 AM »
Previous owner of my 22WSM notched it. I actually think it’s pretty handy with multiple probe wires.
Sent from my iPhone using
Weber Kettle Club
Logged
walley_eye
Smokey Joe
Posts: 61
Re: Ry and his Dremel cut
«
Reply #8 on:
August 04, 2020, 05:03:20 PM »
I usually run my wire down through bottom vent and out ash can holes and then run the probe up through the side of the grate over the top.
No drilling.
Sent from my iPhone using Tapatalk
Logged
Print
Pages: [
1
]
« previous
next »
Weber Kettle Club Forums
»
Cooking & Food Talk
»
Charcoal Grilling & BBQ
(Moderators:
SixZeroFour
,
Cellar2ful
) »
Ry and his Dremel cut