The front section left of center post was grinded with the dremmel grinding cylinder shown. The section on the right was a) scraped with a razor and then b) "brushed" with the dremmel soft abrasive shown.
Both ways leave a less than perfect result. I'm trying to stay away from evaporust/chemicals, but may not have a choice.
Any suggestions to get this triangle back to "right"?
WTB: rubber-treaded wheels for 22" 69-70 Pat Pending.
Evapo rust is the best, easiest and probably the most effective way to handle that.
Sent from my SM-G960U using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
Evapo-Rust is safe to use, not caustic, and reusable. You need something to get into the pitting that's occurred. If sticking with a mechanical fix, consider a wire brush on a drill or the Dremel.
A few other tips that might help, http://weberkettleclub.com/weber-charcoal-grill-restoration/triangle-restoration-rust-removal/
Or, there's part #80695 depending on what your time is worth.
I've been searching for a post I read some time ago that perfectly explained the electrolysis method... can't seem to locate. May give that a shot.
WTB: rubber-treaded wheels for 22" 69-70 Pat Pending.
Maybe this is the post? Not sure this would work on a triangle the way it did on CI, you might end up having to paint. Worth a try.
http://weberkettleclub.com/blog/2014/08/22/camp-oven-restored-using-electrolysis/ (http://weberkettleclub.com/blog/2014/08/22/camp-oven-restored-using-electrolysis/)
Lately, I've been wrapping each spoke of the triangle in paper towels, then soaking in white vinegar overnight in a trash bag. This loosens most of the rust.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Quote from: Mr.CPHo on June 16, 2018, 08:44:41 AM
Lately, I've been wrapping each spoke of the triangle in paper towels, then soaking in white vinegar overnight in a trash bag. This loosens most of the rust.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Good, cheap idea. I bet if I do this overnight, it will loosen it enough that my dremmel soft polishers will take care of the rest. Gonna give it ta try.
Thanks!
WTB: rubber-treaded wheels for 22" 69-70 Pat Pending.
Quote from: 56MPG on June 16, 2018, 07:13:32 AM
Maybe this is the post? Not sure this would work on a triangle the way it did on CI, you might end up having to paint. Worth a try.
http://weberkettleclub.com/blog/2014/08/22/camp-oven-restored-using-electrolysis/ (http://weberkettleclub.com/blog/2014/08/22/camp-oven-restored-using-electrolysis/)
Thanks @56MPG ... that's exactly what I was looking for. From what I've read, it should work just as well on a triangle.
WTB: rubber-treaded wheels for 22" 69-70 Pat Pending.
I'm reading from Good authority that you should not use stainless steel in the electrolysis process as the alloys used break down into a carcinogen.
Is a triangle support stainless steel?
WTB: rubber-treaded wheels for 22" 69-70 Pat Pending.
Wishful thinking. Triangles are not stainless. Give it a shot. (jolt?)
Marty's right on. If they were SS
We wouldn't be having this discussion. A Dremel seems kind a wimpy choice to me.
Oscillating multitool with 220 and a light touch might be the better way to go. Evaporust is a hell of lot less trouble andmess than electrolysis. Biggest pain with a triangle is finding a large enough shallow container. I've used a trash bag laid down in a cardboard tray. Just be sure not to poke any holes in the bag.
Then just snip the corner of the bag to drain back into jug.
Sent from my XT1650 using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
Stop being a weirdo and go get some evaporust and be done with it.
Those little wire wheels for the dremel work awesome though in the crevices when you have a triangle in better shape to work with.
Does anybody have a trick to keep them from re-rusting spelt after cleaning? I've razor bladed a few clean but then a month later they look terrible again
Quote from: Mr.CPHo on June 16, 2018, 08:44:41 AM
Lately, I've been wrapping each spoke of the triangle in paper towels, then soaking in white vinegar overnight in a trash bag. This loosens most of the rust.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
[/quote
Phosphoric acid works good also (Coca-Cola).
Quote from: jkolantern on June 16, 2018, 05:29:25 PM
Does anybody have a trick to keep them from re-rusting spelt after cleaning? I've razor bladed a few clean but then a month later they look terrible again
The only "trick" I can think of is to take them to someone who will sandblast them and powdercoat them.
Or after you prep them, keep hitting them with black BBQ paint as needed.
Paint being the common theme here.
On the other hand, since these don't see high heat, perhaps there's some kinda clearcoat that will work, to retain the chromey look?
Clearcoat out of a rattle can blows in my experience. It doesn't hold up to UV rays and turns yellow over time. Would be interesting to drop off the triangle at a car paint shop though and have them hit it with a few coats of high quality clearcoat at the end of a job.
Hmmm. There's clearcoat available in powder coat as well. Maybe I'll take one for the team.
Quote from: jkolantern on June 16, 2018, 05:29:25 PM
Does anybody have a trick to keep them from re-rusting spelt after cleaning? I've razor bladed a few clean but then a month later they look terrible again
Nevr-Dull wadding polish.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
3 coats of non-yellowing clear coat over 2 coats of chrome paint.
The clear I like is the semi gloss.
Eastwood Chrome powder.
https://www.youtube.com/watch?v=J9XW8zokU8w (https://www.youtube.com/watch?v=J9XW8zokU8w)