This is my first of many orders from
@zavod44 I asked for something special and boy, did he deliver. After a bit of back and fourth. This is what I got.
(http://i1222.photobucket.com/albums/dd487/sickofcichlids/AE1E383E-7C76-474E-BA9B-87E56B45BBD5.jpg) (http://s1222.photobucket.com/user/sickofcichlids/media/AE1E383E-7C76-474E-BA9B-87E56B45BBD5.jpg.html)
Just in time for hockey season.
@JDD GOHAWKS!!!
Wow, his craftsmanship is just out of this world!
Quote from: WNC on September 12, 2015, 07:16:27 PM
Wow, his craftsmanship is just out of this world!
Almost don't want to use them... That negates the respect part of RRR, IMO though.
Nice!
Very cool, I love it!! Somebody (I can't remember who) posted a picture of a red kettle/black lid or visa versa. I would love to do a Hawks kettle with these handles.
@TheDude
@JDD They are going on a black OTP for now. If I ever find a redhead, I'll be doing some rearranging. Or just get another set.
Oh I can make more. Show some pics when you get the wood rollers on and get it all done....
@zavod44 What woods can u use to make handles and rollers for a ss performer?
Like what do I have on hand or what can be made? Send me a PM and we can discuss
Quote from: zavod44 on September 14, 2015, 07:22:17 PM
Oh I can make more. Show some pics when you get the wood rollers on and get it all done....
Oh, I've got some ideas...
Most of the way mounted, except one roller. The lid bale nut on the back side won't budge. I've tried Mean Green and zippo fluid. Thing won't move. Even twisted the bale a bit.
(http://i1222.photobucket.com/albums/dd487/sickofcichlids/0F48E4DC-F48C-4830-990D-7D24FA222803.jpg) (http://s1222.photobucket.com/user/sickofcichlids/media/0F48E4DC-F48C-4830-990D-7D24FA222803.jpg.html)
(http://i1222.photobucket.com/albums/dd487/sickofcichlids/03CFBF79-C82F-421D-8237-1D964C86E170.jpg) (http://s1222.photobucket.com/user/sickofcichlids/media/03CFBF79-C82F-421D-8237-1D964C86E170.jpg.html)
@zavod44 @SixZeroFour @pbe gummi bear
Dremeling the nut off is the safest way imo. A torch may hurt the porcelain. Alternatively you can try a rust penetratant but wash it off before you cook.
forgive me. I'm not super handy. If I dremel off that portion of the bale, how would I reinstall it?
@TheDudeThe Mean Green Cleaner you are using is a good degreaser, but what you need is a penetrating oil to get down into the threads of the bale and get rid of the rust. Do you have anything like PB Blaster handy? Give it a good spray and allow it to soak for 5 min. Next use a wire brush to scrub at the nut as best as possible to help loosen any rust at the surface. Re-spray with a healthy shot of the penetrating oil almost using it to flush away the mess left by the wire brush and then allow it to sit for at least an hour - longer if you're patient ;)
Oh and if possible use a 6-sided socket as opposed to a wrench or a 12-sided as you will maximize your torque on the nut without stripping the corners off.
Good Luck, and keep us posted!
If you wanted to use the heat method you could try lighting a basket of fuel and leave it under the nut, let it heat up then move the basket and try loosening it with a spanner while wearing gloves
For thumbscrews I used wd40, let it sit and they wouldn't budge. Went down the next morning and after sitting all night I was able to get them off with pliers.
Picked up a can of PB Blaster. Will post results.
So far, no go. Gonna let it sit over night. Might be on the market for a bale wire, if anyone has one laying around.
PB Blaster is good stuff. I would spray it again before bed trying to get it into the threads, let it sit till tomorrow.
If it is still tight, don't keep turning or you may twist it in half breaking it.
Do what Hogsy said,,,,light some charcoal, put the lid on and let it heat up real hot inside. Then put the wrench or socket on it and try easy. If it wont budge, let it heat more, can spray more PB Blaster on it, but don't spray on the charcoal. Let her heat up good and try again.
Heat normally works for a rusted bolt.
PB should do it, you can keep applying it, the heat should help too, be patient, as these other guys said even the most stubborn bolts usually come loose. Even if it takes a few days it's still faster than ordering a new one and having it delivered......
Tried heat all day. Thing isn't budging. Tabs on the bail outside the bowl are about vertical. At this point, I think it's cross threaded more so than rusted.
Quote from: TheDude on September 15, 2015, 03:10:28 PM
So far, no go. Gonna let it sit over night. Might be on the market for a bale wire, if anyone has one laying around.
I have 2.
PM sent.
Those nuts usually come off without too much effort. I agree on the cross threading.
Take some duct tape to the outside of the bale and use a good pair of vise grips to hold it while using a socket to remove the nut.
The tame should protect the bale form getting too scuffed up.
A little heat from a torch isn't going to hurt the porcelain.. Just don;t go overboard with it.
It's on it's way !
Thing still won't budge, but
@Camp to a generous rescue.
@TheDude I agree w/ Gummy Bear, I'd use my Dremel Tool w/ my smallest cut-off bit. The cut is carefully along the axis of the bail ... the trick is to cut a slot in the nut that goes down to the level of the threads. A flat blade screw driver should then be able to loosen (or even break) the nut. Easy off at that point. SJ
@Camp 's new bale arrived today. Very dude of you man! Now to get the old one off and get everything mounted. Thanks guys!! This community rocks!
Where did this end up? I'm dying to see the finished product!
Still jacking with the bale, but I've got this for ya.
(http://i1222.photobucket.com/albums/dd487/sickofcichlids/48086D24-914C-4FC2-8679-5273DBD66FB1.jpg) (http://s1222.photobucket.com/user/sickofcichlids/media/48086D24-914C-4FC2-8679-5273DBD66FB1.jpg.html)
It's off!
(http://i1222.photobucket.com/albums/dd487/sickofcichlids/F1588D3E-0D07-4F8B-91F0-01EA0F6C3476.jpg) (http://s1222.photobucket.com/user/sickofcichlids/media/F1588D3E-0D07-4F8B-91F0-01EA0F6C3476.jpg.html)