I've decided that I want to make an ash pan for my 26" Chief.
(http://i576.photobucket.com/albums/ss208/BigRix/Cooking%20on%20the%20Weber/69998383-ACD7-48DF-A2B6-D7FA814DD152_zpsg6daz1zh.jpg) (http://s576.photobucket.com/user/BigRix/media/Cooking%20on%20the%20Weber/69998383-ACD7-48DF-A2B6-D7FA814DD152_zpsg6daz1zh.jpg.html)
I'm thinking about starting with a bowl of some kind and modifying it.
What I need is the dimensions of the original pan.
Overall width, depth and measurements of the slots.
Pics of a pan with a tape measure would be awesome.
I'm not to concerned with the material I use, but I want to try and match the shape as close as possible.
If I can find a good candidate bowl I will pass along any sourcing info and do a write up on the mods.
Rix, I know the 22" twist discs have the same contour as the bottom of a 22" bowl.
Guys with a 26" ashpan, can you check if it's contoured to the 26" or 22" bowl?
GL with this!
I know these aren't going to be too helpful, but its a place to start and see how it sits on the legs. I'll try and measure up some pics later.
(http://i442.photobucket.com/albums/qq142/A_Tame76/red%2026/Big%20Red/BigRed1_zps55247bae.jpg)
(http://i442.photobucket.com/albums/qq142/A_Tame76/red%2026/Big%20Red/DSCF8406_zpse8cdef89.jpg)
(http://i442.photobucket.com/albums/qq142/A_Tame76/red%2026/Big%20Red/DSCF8407_zps3ae4df11.jpg)
26" twist pan has got to be the single hardest part to find. I wish I had access to a metal shop for fabricating one.
if someone wants to draw up the details in solidworks or some other engineering software, I can hit some of the fab shops near me and get some quotes.
The metal working guy next to me said it'd probably cost $10 to make ;)
Quote from: Troy on July 11, 2014, 09:00:07 AM
if someone wants to draw up the details in solidworks or some other engineering software, I can hit some of the fab shops near me and get some quotes.
The metal working guy next to me said it'd probably cost $10 to make ;)
And seriously - if that's the case - i'll have a dozen or so made and sell them at cost.
Quote from: Troy on July 11, 2014, 09:00:40 AM
Quote from: Troy on July 11, 2014, 09:00:07 AM
if someone wants to draw up the details in solidworks or some other engineering software, I can hit some of the fab shops near me and get some quotes.
The metal working guy next to me said it'd probably cost $10 to make ;)
And seriously - if that's the case - i'll have a dozen or so made and sell them at cost.
That would be awesome
Did someone say engineer?
(https://scontent-b.xx.fbcdn.net/hphotos-xpf1/t31.0-8/981316_986916060148_1971323622_o.jpg)
(https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-xap1/t31.0-8/1015676_986916065138_518274559_o.jpg)
(https://scontent-a.xx.fbcdn.net/hphotos-xfa1/t31.0-8/1048114_986916050168_279711134_o.jpg)
(https://scontent-a.xx.fbcdn.net/hphotos-frc3/t1.0-9/9086_10100109052484748_886906739_n.jpg)
Put me first in line if you get some of those made up.
In the meantime, I'm thinking of starting with a wok like this one at a local Asian market.
(http://i576.photobucket.com/albums/ss208/BigRix/Cooking%20on%20the%20Weber/CA516686-54A2-4442-A0C6-455F9155A973_zpshfeaimsf.jpg) (http://s576.photobucket.com/user/BigRix/media/Cooking%20on%20the%20Weber/CA516686-54A2-4442-A0C6-455F9155A973_zpshfeaimsf.jpg.html)
It's about 20" across and would most likely catch more ashes than an original.
genius!
Quote from: Troy on July 11, 2014, 09:00:40 AM
Quote from: Troy on July 11, 2014, 09:00:07 AM
if someone wants to draw up the details in solidworks or some other engineering software, I can hit some of the fab shops near me and get some quotes.
The metal working guy next to me said it'd probably cost $10 to make ;)
And seriously - if that's the case - i'll have a dozen or so made and sell them at cost.
Any chance you could get some 22 ashpans made, too? I have one kettle from '79 that was missing it and I didn't want to get the clip on style.
the wok is an idea I've had rolling around in the brain pan for awhile......might work real good !!!!
I have a throatless shear for cutting crazy stuff out like that.....could work for most of the cuts, but might have to switch to Dremel for the very tight angles..........
Troy, Id be in for 1 for sure!
Just curious, were the originals spun or stamped?
Stamped. I don't see the spinning rings on them.
BigRix,
If you go with the wok idea, and are not dead set on a twist on style, you could always go this route:
(https://dl.dropbox.com/s/93dff0btjyei546/Black%206.jpg)
Winz
Quote from: Troy on July 11, 2014, 09:00:40 AM
Quote from: Troy on July 11, 2014, 09:00:07 AM
if someone wants to draw up the details in solidworks or some other engineering software, I can hit some of the fab shops near me and get some quotes.
The metal working guy next to me said it'd probably cost $10 to make ;)
And seriously - if that's the case - i'll have a dozen or so made and sell them at cost.
This has to be the ticket guys.
I Havent forgot about this. Im gonna get some measurements and photos on Sunday for this.
Hopefully these photos are a little helpful for you.
First pic is measured across the pan from end to end. Came to 18"
(http://i442.photobucket.com/albums/qq142/A_Tame76/red%2026/DSCF0158_zps5e77f1d8.jpg)
Second pic is with the tape measure flat inside the curve of the pan. Came to just over 19"
(http://i442.photobucket.com/albums/qq142/A_Tame76/red%2026/DSCF0159_zpsb3ae6f86.jpg)
Third pic is from center of each leg cutout. That was about 13"
(http://i442.photobucket.com/albums/qq142/A_Tame76/red%2026/DSCF0162_zps4d72be3c.jpg)
Fourth pic was the height of the pan. Came to about 4"
(http://i442.photobucket.com/albums/qq142/A_Tame76/red%2026/DSCF0161_zpsa9e450ac.jpg)
Last pic showing how it sits on the legs.
(http://i442.photobucket.com/albums/qq142/A_Tame76/red%2026/DSCF0163_zps6729c004.jpg)
How far down the legs does it sit. Looks like about 5"
Mine sits 5-1/4" level. Measured from the bottom base down. Been busy today. Would a side by side help?(22 next to a 26)
Mine sits about 6" down from the base of the bowl.
Quote from: Winz on July 11, 2014, 08:15:03 PM
BigRix,
If you go with the wok idea, and are not dead set on a twist on style, you could always go this route:
(https://dl.dropbox.com/s/93dff0btjyei546/Black%206.jpg)
Winz
I think I might try this type of set up with the wok.
Does this ash pan have the same measurements as the twist style?
Winz, did you have any more of those clips made up? If so, I would like to buy some from you.
This seems like the easiest to make out of a wok. Hole saw and a dremel for the slots and a drill and rivets or bolts for the clips.
Winz, what did you use to attach the clips? I forgot and can't find your post again.
Do y'all think ash would help season the wok and I could still cook on it? :)
Quote from: BigRix on July 14, 2014, 06:11:42 AM
Do y'all think ash would help season the wok and I could still cook on it? :)
That's what I like most about folks here.......always thinkin'....always thinkin'....... 8)
QuoteWinz, did you have any more of those clips made up? If so, I would like to buy some from you.
This seems like the easiest to make out of a wok. Hole saw and a dremel for the slots and a drill and rivets or bolts for the clips.
Winz, what did you use to attach the clips? I forgot and can't find your post again.
Just sent out my last set to another WKC member, but I can have some made for you this week. Just let me know. The hooks will be punched but not drilled - that way you can choose your own diameter fastener. I used little bolts but rivets would work just fine.
Winz
I actually have an extra set I got from Winz. I can share them if you need them. If you want them send me a message. I used small pop rivets on mine
I was cleaning my kettles this weekend and noticed that the rolled edge twist pan I have fits the 26"... it's high up on the legs (just over 2" from the bottom of the bowl). My flat top is an H, so it has the One Touch system. It catches all the ash, no problem. Not sure if that type of twist pan would work with a daisy wheel 26er, though....
Yeah the old 22 twists WILL fit a 26er but they do sit high up against the bowl. Its almost the equivelet of an 18 pan sitting up under a 22 bowl.