Welcome, Guest
Login or Register

Shop Amazon.com and support the WKC | WKC T-Shirts
« previous next »
Pages: [1]

Author Topic: Kettle Wheel Upgrade  (Read 5225 times)

DirectDrive

  • WKC Ranger
  • Posts: 867
Kettle Wheel Upgrade
« on: July 24, 2016, 05:51:18 PM »
I'm not a fan of the OEM plastic wheels with their flimsy construction, inside spider pockets and Jeep tread.
I've seen where some have used golf cart wheels or lawnmower wheels for replacements, so I thought I'd give it a go.

I used these wheels...


The operating room...

Tools front to back...
Hubcap tool
Sharpie (not used)
Pen - used to mark cuts on shaft spacers
Mylar tape - used to shim shaft spacers
Small pry bar
Utility knife - for trimming Mylar tape
Scissors - for cutting tape
Pliers - for holding shaft spacers while cutting
Bastard file - for touching up OD of spacers
Chainsaw file - for touching up ID of spacers
4-1/2" angle grinder w/cut-off disk - for cutting shaft spacers


Re-used the Weber "hubcaps" (push nuts)
The wheels have two ball bearings per wheel. (overkill, but cool)


These wheels have a 1-1/2" long hub which is about the same as OEM but they have 1-3/4" wide tread which is 1/4" wider than OEM.
I used two nylon washers to space the wheels away from the legs.



Most of the lawmower wheels have a 1/2" ID bearing bore.
The kettle has a 3/8"OD axle so you need a 3/8" - 1/2" shaft spacer.
I ended up with low tech, "rolled" spacers which needed Mylar tape shimming on their OD to snug up to the bearings.
Mylar doesn't compress much so it makes good thin shimstock, where electrical tape would be a bad choice because of it softness.
My shaft spacers were too long and had to be cut down to match the hub length.

It was an easy mod and I'm happy with the stoutness and the look.
Kind of "Little Red Wagon" retro.

« Last Edit: July 25, 2016, 03:59:50 PM by DirectDrive »
Logged

AZ Monsoon

  • WKC Ranger
  • Posts: 746
Re: Kettle Wheel Upgrade
« Reply #1 on: July 24, 2016, 06:02:55 PM »
Looking good!
« Last Edit: July 24, 2016, 06:53:31 PM by AZ Monsoon »
Logged

charred

  • WKC Performer
  • Posts: 2291
Re: Kettle Wheel Upgrade
« Reply #2 on: July 24, 2016, 09:03:53 PM »
Pretty cool!
Logged
hopelessly, helplessly, happily addicted to a shipload of Webers

captjoe06

  • WKC Performer
  • Posts: 2829
    • Northeast BBQ
Re: Kettle Wheel Upgrade
« Reply #3 on: July 25, 2016, 03:40:51 AM »
I love the look and the idea.  Really solid.  Nice work.
Logged
Smokey Joe Black, Smokey Joe Lime Green, Original Kettle Premium Black,'92 Red OTS, Yellow Simpson's 22, 78 Red MBH, '80 Black MBH, '10 Brick Red Performer,'12 Grass Green Performer, '03 Blue SSP, '97 Blue SSP, 18 inch WSM

haeffb

  • WKC Ranger
  • Posts: 674
Re: Kettle Wheel Upgrade
« Reply #4 on: July 25, 2016, 04:05:28 AM »
What is the "hubcap tool?"

And what is the source of the shaft spacers?
Logged

DirectDrive

  • WKC Ranger
  • Posts: 867
Re: Kettle Wheel Upgrade
« Reply #5 on: July 25, 2016, 04:33:41 AM »
Quote from: haeffb on July 25, 2016, 04:05:28 AM
What is the "hubcap tool?"
The hub cap tool is the first tool in the pic.
It's an automotive tool, but also works well for removing the Weber hubcaps.
The small prybar in the pic and the hubcap tool are used together to get the Weber hubcap off.

A pair of "glazer's prybars" would probably be the ideal tools for getting the Weber hubcaps off.

Quote
And what is the source of the shaft spacers?
Seller : mowerpartsworldwide
« Last Edit: July 25, 2016, 04:02:29 PM by DirectDrive »
Logged

DarrenC

  • WKC Brave
  • Posts: 217
Re: Kettle Wheel Upgrade
« Reply #6 on: July 25, 2016, 05:57:11 AM »
Spectacular mod!  Thanks for sharing the idea!
Logged
"There are a great many things one can learn to do without actually doing them - Grilling is not one of them" - Alton Brown

Hell Fire Grill

  • WKC Performer
  • Posts: 2049
Re: Kettle Wheel Upgrade
« Reply #7 on: July 25, 2016, 06:34:19 AM »
I seen some wheels that looked very similar to those at Duck's the other day, but they'd probly need to have wheel bushings to. The bushings might be available at Wilco or Vancouver bolt.
Logged
You can't always get what you want....but if you try sometimes you get what you need

DirectDrive

  • WKC Ranger
  • Posts: 867
Re: Kettle Wheel Upgrade
« Reply #8 on: July 25, 2016, 04:24:12 PM »
Quote from: Hell Fire Grill on July 25, 2016, 06:34:19 AM
I seen some wheels that looked very similar to those at Duck's the other day, but they'd probly need to have wheel bushings to. The bushings might be available at Wilco or Vancouver bolt.
You're from my 'hood !

Parkrose Hardware has precision shaft spacers that are the correct length (1-1/2") but they would have required some "tuning" to get
them to fit.
They were tight on the Weber axle and tight into the wheel bearings.
Only .95 each, though.

"Arnold" brand lawnmower wheels are available at Lowe's but I didn't like the specs.
The hub length at 1-3/4" and the color (bluish gray) didn't fit my plan.
Very happy with the ones I used.

Logged
Pages: [1]
« previous next »