Hello everyone. Newbie to this site. I have had a Weber kettle for several years now. I cooked on it for quite a while, then got away from it and tried new pits. I got away from it because my lid was warped and it was difficult to maintain temps. Now I am wanting to get a new master touch. My question is, what mods would you guys suggest for this new grill. I already have an igrill with 4 probes, and I am ordering a silicone probe grommet for it. I would like to use some sort of fan system to maintain temps, and would like to find a ring to make it taller and increase my total cooking space. Other than that, I don't know what else I should do. I will mainly use it for smoking ribs, butts and briskets. I have a slow-n-sear from my other kettle. Any suggestions would be appreciated. Glad to be getting back into the Weber game!
Kevin
Practice, practice, practice.
100lbs of charcoal and 50lbs of meat!
I recommend trying it stock first with the slow n sear you have. See how you like it, may not need the fancy blower system. I've not seen the need for one personally. Cajun Bandit has nice riser rings....
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I'm with @bamakettles get to know it first, you may decide no mods needed
Sent from my SM-G975U using Tapatalk
Etching 1/3 markings for sweeps so you know how far you have it open. I put on a hinge kit, but it can be hard on my back to try to pull it at the correct angle to get it to close.
I have been waiting till I have money to justify buying a temp control fan system, not sure which to get. I also would like to build a heat deflector like you find in a kamado, but can't find the right material at the right price.
Get a second charcoal grate to add cross ways to the existing one so charcoal has to burn down smaller up fall through. Your slow n sear should prevent a lot of that though when you use it.
All I can think of right now though.
^^^
This, but I went a little further.
The cut out "settings" are at best "Off" so I used a Dremel with a SMALL round grindstone to set the actual CLOSED, 1/4, 1/2, 3/4 & FULL positions of the blades in the inside. By making some small semi-circular scallops in the bottom edge the lever now has "click stops" where the lever drops into them, so I don't have to look under the kettle!
The newer Master Touch has pre-drilled dots on its ash catcher ring for smoke settings.
If you are looking for risers:
https://www.etsy.com/shop/SpitfireGrilling?ref=simple-shop-header-name&listing_id=604270812
I'd just use the ring from my rotisserie as a spacer?
Yes there are markers on the new master touch, but check out how well they align (or not) with the scraper blade positions!
My "detents" are actually set using them as a guide for position & a re considerably different.
These were the original magic marker set that i used to test it. sorry they're a little fuzzy.
(https://i.imgur.com/ilCspy2.jpg)
https://www.youtube.com/watch?v=a8U9f8Q611M
Quote from: RRRanger99 on January 25, 2022, 08:37:28 PM
https://www.youtube.com/watch?v=a8U9f8Q611M
I think that grill is discontinued. It's not on the Weber website anymore. Seemed overpriced to me but I liked the diffuser concept and wsm-esq charcoal ring. I always wanted to build a set up like it.
Sent from my iPhone using Tapatalk
@michaelmilitello Yes, that Master Touch Premium grill is discontinued in the U.S. (Still available to the rest of the world). Those dot indicators are on every new 2019+ Master Touch grill ash catcher ring, with the newer "p,"
vent bowl. The video is just showing what the dots are used for.
Quote from: michaelmilitello on January 26, 2022, 07:14:08 PM
Quote from: RRRanger99 on January 25, 2022, 08:37:28 PM
https://www.youtube.com/watch?v=a8U9f8Q611M
I think that grill is discontinued. It's not on the Weber website anymore. Seemed overpriced to me but I liked the diffuser concept and wsm-esq charcoal ring. I always wanted to build a set up like it.
Sent from my iPhone using Tapatalk
Cant even find parts for them in the US anymore either, unless you call Weber directly I suppose. Shame, too. If the replacement bowl for my Performer didn't already have holes for the lid bail, I was considering an unknown BBQ hinge, and then some touches from the MTP like these fellas did:
Quote from: michaelmilitello on January 26, 2022, 07:14:08 PM
Quote from: RRRanger99 on January 25, 2022, 08:37:28 PM
https://www.youtube.com/watch?v=a8U9f8Q611M
I think that grill is discontinued. It's not on the Weber website anymore. Seemed overpriced to me but I liked the diffuser concept and wsm-esq charcoal ring. I always wanted to build a set up like it.
Sent from my iPhone using Tapatalk
Someone on another thread put up a link to Heat Beacon designs for a tool holder so I clicked on it. Then of course started looking at other stuff and found they sell a diffuser plate set up. It might be worth looking at instead of the hassle of building your own
https://www.heatbeacondesigns.com/shop-products/p/deflector-plate-and-charcoal-ring
Quote from: BigEasy on January 28, 2022, 05:44:02 AM
Quote from: michaelmilitello on January 26, 2022, 07:14:08 PM
Quote from: RRRanger99 on January 25, 2022, 08:37:28 PM
https://www.youtube.com/watch?v=a8U9f8Q611M
I think that grill is discontinued. It's not on the Weber website anymore. Seemed overpriced to me but I liked the diffuser concept and wsm-esq charcoal ring. I always wanted to build a set up like it.
Sent from my iPhone using Tapatalk
Someone on another thread put up a link to Heat Beacon designs for a tool holder so I clicked on it. Then of course started looking at other stuff and found they sell a diffuser plate set up. It might be worth looking at instead of the hassle of building your own
https://www.heatbeacondesigns.com/shop-products/p/deflector-plate-and-charcoal-ring
The diffuser plate and charcoal ring from them work really well. It's a high quality product.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
My Costco has MT Premiums in stock.
As for mods, I love my River City Woodworks handles and vent tab, and the gasket on the lid. The gasket is more for dampening vibration than sealing. It makes the lid feel more solid and less tinny.
The best accessory is a Cajun Bandit rotisserie kit.
Sent from my iPad using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
$299.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Unfortunately, we do not have a Costco here.
Where is that Costco located?
It looks like that poor thing is about to lose it's ash catcher.
Sent from my SM-G975U using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
La Habra, CA
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Way to get back into the Weber game! For me, I put a LavaLock 5/8" x 1/8" graphite-impregnated fiberglass flat gasket on the bottom of the rim on all of my kettle lids and WSM lids before I ever put fire in them. They come 84" long which is enough to do a full 26" lid. I'm not a huge fan of stainless steel grates and I'd have my eyes on a set of Craycort grates for it at some point down the road. Slow-N-Sear Drip 'N Roast pan is also a nice accessory to have below the grate. I also never dug the 8" wheels on the newer kettles and Performers and I'd get some older generation 8" wheels or even Summit Charcoal wheels for it instead of the ones it comes with.