Weber Kettle Club Forums

Grill Talk => Weber Kettle Forum => Topic started by: BobInCalifornia on December 05, 2016, 05:09:23 PM

Title: Need help from the masters on 1 gal tank replacement on old style Performer
Post by: BobInCalifornia on December 05, 2016, 05:09:23 PM
I need the gurus!

I have a lovely new Performer but kept my original (90's) Performer touch-n-go as well.  I have reach the dreaded expired tank stage and in addition to no one really wanting to fill a 1 gal tank with a 1/4" type II quick disconnected (CGA 810), now they legally can't.

In looking for a replacement tank it seems like they really aren't made with the CGA 810 any more... so I would like to move to a 5 gal tank (like I did on my new Performer) which will require a hose from the Type 1 connector on the new tanks to a female CGA 810.  I can't find that adapter hose anywhere.

Did I complete misunderstand what I need to do?

Thanks for any suggestions from you wise forum members!
Title: Re: Need help from the masters on 1 gal tank replacement on old style Performer
Post by: varekai on December 05, 2016, 08:00:31 PM
@BobInCalifornia , I posed that same question to an RV repair/ propane sales store here in my town, They said they would fill no problem. I had another tank re certified and it was only $5... FWIW.   And welcome to the club.
Title: Re: Need help from the masters on 1 gal tank replacement on old style Performer
Post by: BobInCalifornia on December 06, 2016, 04:44:55 PM
I may have to come up to Paso Robles to get it done... I am in Santa Monica and no one seems to want to touch either the recent or the tank.  I have increased my search to RV places now though!  My mother is in Lompoc so it isn't much of a haul to get to PR from there if you have a place that can handle it!

The problem is that when the grill makers abandoned QC, so did the tank makers.  There are a zillion connection types... but if any one knows of a Type I (Acme) to Type II (810 CGA) hose that is 3-5' let me know... that would put the issue back in the realm of supported products!
Title: Re: Need help from the masters on 1 gal tank replacement on old style Performer
Post by: Hell Fire Grill on December 09, 2016, 05:44:23 PM
Bob a RV repair should be able to make a hose to do what you want it to. They'll probably need to reuse part of the original gas line/orifice from your performer to make a new one with whatever connector you want.
Title: Re: Need help from the masters on 1 gal tank replacement on old style Performer
Post by: swamprb on December 10, 2016, 09:04:46 AM
Not sure if this is what you are getting at, but I just get an ACME fitting and swap out the old QR fitting. If you have a new OPV tank.

https://www.google.com/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=acme+fittings++Mr+Heater&tbm=shop

So basically what I do is remove the QR fitting and replace it with the Acme nut. A deep socket (forget the size) gets it done. Use some pipe dope on the treads.

https://www.google.com/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=acme+fittings++Mr+Heater&tbm=shop&spd=11032951487953882384

This is an old mod I did on my Performer T&G so I could also use the disposable tanks-or run a bulk 5 gallon tank via a Q bulk hose.

Its a Harbor Freight refill adapter on the old style POL fitting.

(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/100_1838.jpg)

(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/100_1839.jpg)

(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/100_1840.jpg)

My local ACE has all the Mr Heater fittings to get the mod done.

I've been able to remove some of the tank QR fittings and just take them off when I get the tank refilled. I use the male end on my Harbor Freight weed torches and use the female QR's in smaller tanks.

Hope this helps!