Rising from the rust and ashes -
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_2427.jpg)
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_2423.jpg)
The Green OTP will live on to grill into eternity!
As the Master-Touch Platinum!
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_2432.jpg)
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_2433.jpg)
Table top got a needed pressure wash, wire shelf sand blasted and repainted with Hammered Finish paint along with the frame.
I removed the bowl brackets, lightly blasted and used Dupli-Color Engine Red paint. Stainless machine bolts secure them.
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_2430.jpg)
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_2435.jpg)
The Master-Touch is a rescued "EZ" 1998, I used the vent handle from the original "DD" Greenie and used an old style grooved handle from a Weber chimney to match. Not much of an age difference!
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_2436.jpg)
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_2437.jpg)
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_2438.jpg)
I agonized over which kettle to drop in, but the logical choice was the Master-Touch as it only has one bowl handle (which had a broken weld and was bolted on) and all my other Redhead kettles have two handles. I used some nickel plated hole plugs drilled out and secured with stainless acorn nuts. Not pretty, but it works for me.
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_2439.jpg)
Thanks for looking, this was an easy mod!
Brian
Awesome work here! That M/T will live to ride again.
How did you remove the bowl brackets? Pry 'em until they just gave it up? Or cut?
Quote from: addicted-to-smoke on March 29, 2016, 06:09:01 PM
Awesome work here! That M/T will live to ride again.
How did you remove the bowl brackets? Pry 'em until they just gave it up? Or cut?
I took a tip from
@Troy and tried to drill at the welds inside the bowl. There were 3 small spot welds which made it pretty difficult, but patience prevailed.
Reminds me of the 26 I just picked up. Needs TLC. Both side handles' welds are loose. How? Why? Lid handle weld is fine but the hangar bracket is bent/doesn't hold. Leg sockets look like your M/T on the inside (as in, not good) but sockets are strong. I need to save up for a miniRanch frame mod unless a table that's not too huge comes along.
Beautiful!
Looks nice, but the bottom grate shelf is upside down
Great work looks awesome.
Quote from: addicted-to-smoke on March 29, 2016, 06:09:01 PM
How did you remove the bowl brackets? Pry 'em until they just gave it up?
Those spot welds are quite strong so I would not recommend doing this. Ive done it once to a handle and will never again.
Quote from: Harleysmoker on March 29, 2016, 06:53:43 PM
Looks nice, but the bottom grate shelf is upside down
Thanks but it is on correctly!
Quote from: pbe gummi bear on March 29, 2016, 07:26:56 PM
Quote from: addicted-to-smoke on March 29, 2016, 06:09:01 PM
How did you remove the bowl brackets? Pry 'em until they just gave it up?
Those spot welds are quite strong so I would not recommend doing this. Ive done it once to a handle and will never again.
Not for the faint of heart!
Nice work. She's a sexy redhead now!!! Looks dang near factory.
That is excellent work! It should look remarkable with a CB Stacker.
Quote from: swamprb on March 29, 2016, 07:58:16 PM
Quote from: pbe gummi bear on March 29, 2016, 07:26:56 PM
Quote from: addicted-to-smoke on March 29, 2016, 06:09:01 PM
How did you remove the bowl brackets? Pry 'em until they just gave it up?
Those spot welds are quite strong so I would not recommend doing this. Ive done it once to a handle and will never again.
Not for the faint of heart!
Interesting. I might have tried the angle grinder.
Very nice work.
I've never seen a red OTP. Did Weber ever make one?
Don't think so. By the time this table design came out, pretty sure reds were discontinued.
Better than new...and cheaper too.
Nice rescue and restore! I have to get off my ass and finish my red platinum just haven't decided if I want to paint the frame panels and table or not.
Quote from: 1911Ron on March 30, 2016, 06:07:10 AM
Nice rescue and restore! I have to get off my ass and finish my red platinum just haven't decided if I want to paint the frame panels and table or not.
Are yours the white/cream or grey tables and frames?
And does anyone know if the steel Performer table will fit the Platinum?
Quote from: swamprb on March 30, 2016, 06:56:26 AM
Quote from: 1911Ron on March 30, 2016, 06:07:10 AM
Nice rescue and restore! I have to get off my ass and finish my red platinum just haven't decided if I want to paint the frame panels and table or not.
Are yours the white/cream or grey tables and frames?
And does anyone know if the steel Performer table will fit the Platinum?
The Blue has a gray table the Red has the white/cream table that will get color treatment along with the end pieces. The gray table looks to have knock outs for another bolt pattern perhaps for a Performer???
Nice work man!
I drilled the welds from the outside because I couldn't see them from the inside (plus my donor bowl was filled with healthy thai basil plants at the time and I didn't want to lose them)
And as far as I know, the platinum tables and performer tables are exactly the same - so the metal one should fit fine.
if you risk it and it doesn't fit, i'll buy it from you for whatever you paid.