Welcome, Guest

Shop Amazon.com and support the WKC | WKC T-Shirts

Author Topic: ISO Gen 1 Ashbucket and Ring  (Read 59853 times)

bear

  • WKC Ranger
  • Posts: 888
ISO Gen 1 Ashbucket and Ring
« on: July 21, 2019, 03:14:37 PM »
And hex drive sweeps if possible. 
Send me a PM

bear

  • WKC Ranger
  • Posts: 888
Re: ISO Gen 1 Ashbucket and Ring
« Reply #1 on: August 17, 2019, 01:07:54 AM »
Bump

MagnoliaTom

  • WKC Brave
  • Posts: 369
Re: ISO Gen 1 Ashbucket and Ring
« Reply #2 on: August 17, 2019, 04:28:37 AM »
I just got a gen 1 SSP and need one as well. Can you school a newbie on the difference between the original and one I was going to get online?
Part 65143 is what I was looking to get


Sent from my iPhone using Tapatalk
MBH redhead 22”, Smokey joe AU, Q 100, SSP EE code, new 26”
Looking for MBH 26

Walchit

  • WKC Performer
  • Posts: 2141
Re: ISO Gen 1 Ashbucket and Ring
« Reply #3 on: August 17, 2019, 09:48:12 AM »
The older kettles leg sockets aren't oriented properly for the new ring to clip onto. People use different methods to get the new ones to work.

Bob BQ

  • WKC Performer
  • Posts: 4621
Re: ISO Gen 1 Ashbucket and Ring
« Reply #4 on: August 17, 2019, 11:43:22 AM »
I have an extra Gen 1 ring and bar, but no bucket. Might have an extra set of hex nut sweeps... I’ll check.


Sent from my iPhone using Weber Kettle Club
BBQ:it's what's for dinner. Grail: 18” Custom - "The Californian"

MagnoliaTom

  • WKC Brave
  • Posts: 369
Re: ISO Gen 1 Ashbucket and Ring
« Reply #5 on: August 17, 2019, 12:51:12 PM »
The older kettles leg sockets aren't oriented properly for the new ring to clip onto. People use different methods to get the new ones to work.
Thanks for the info!


Sent from my iPhone using Tapatalk
MBH redhead 22”, Smokey joe AU, Q 100, SSP EE code, new 26”
Looking for MBH 26

MagnoliaTom

  • WKC Brave
  • Posts: 369
Re: ISO Gen 1 Ashbucket and Ring
« Reply #6 on: August 18, 2019, 09:29:04 AM »
Can the new sweeps work with the old style pan? Wondering if the mounting tabs on the sweep are long enough to accommodate the bracket that holds the ash pan in place.


Sent from my iPhone using Tapatalk
MBH redhead 22”, Smokey joe AU, Q 100, SSP EE code, new 26”
Looking for MBH 26

MagnoliaTom

  • WKC Brave
  • Posts: 369
Re: ISO Gen 1 Ashbucket and Ring
« Reply #7 on: August 19, 2019, 04:46:20 AM »
Can the new sweeps work with the old style pan? Wondering if the mounting tabs on the sweep are long enough to accommodate the bracket that holds the ash pan in place.


Sent from my iPhone using Tapatalk

After searching I see you need to do a little modification to make it work


Sent from my iPhone using Tapatalk
MBH redhead 22”, Smokey joe AU, Q 100, SSP EE code, new 26”
Looking for MBH 26

bear

  • WKC Ranger
  • Posts: 888
Re: ISO Gen 1 Ashbucket and Ring
« Reply #8 on: August 31, 2019, 05:10:33 PM »
1 found, 1 to go

Jules V.

  • WKC Ranger
  • Posts: 1641
Re: ISO Gen 1 Ashbucket and Ring
« Reply #9 on: August 31, 2019, 06:46:00 PM »
I have a few extra rings but no basket, crossbars or sweeps.

Golly

  • WKC Performer
  • Posts: 2382
Re: ISO Gen 1 Ashbucket and Ring
« Reply #10 on: January 01, 2021, 07:58:03 PM »
I have this @bear


Sent from my iPhone using Weber Kettle Club mobile app
GET ON THAT SHIT
WONT TAKE NO FOR AN ANSWER

PotsieWeber

  • WKC Performer
  • Posts: 2759
Re: ISO Gen 1 Ashbucket and Ring
« Reply #11 on: April 17, 2021, 06:20:09 PM »
@bear
Someone who hasn't been around for quite a long time noticed your message box is full.  Sorry, I didn't get back to you sooner and understand if you've moved on.  Got super busy with the little one "remote learning" and a new client that is regularly sending me stuff with very tight deadlines, so it's been a little nuts for me.

1 found, 1 to go
regards,
Hal

bear

  • WKC Ranger
  • Posts: 888
Re: ISO Gen 1 Ashbucket and Ring
« Reply #12 on: April 17, 2021, 06:55:48 PM »
Inbox clear