Welcome, Guest

Shop Amazon.com and support the WKC | WKC T-Shirts

Author Topic: Wsm 22 table  (Read 2718 times)

ABROB

  • WKC Brave
  • Posts: 274
Wsm 22 table
« on: September 17, 2017, 09:57:56 AM »
Got a performer cheap, sold the kettle to break even.

Built a basic square tubing frame inside the performer frame  and the wsm legs lined up perfectly.

Used a pin through each leg and it is very stable.

[attachment deleted by admin]

Big Dawg

  • WKC Ranger
  • Posts: 1217
Re: Wsm 22 table
« Reply #1 on: September 17, 2017, 11:00:13 AM »
Well Done ! ! !
The Sultans of Swine
22.5 WSM - Fat Boy
22.5 OTG - Little Man/26.75 - Big Kahuna

mhiszem

  • WKC Performer
  • Posts: 3493
Re: Wsm 22 table
« Reply #2 on: September 17, 2017, 11:12:47 AM »
Good looking table!


Sent from my iPhone using Weber Kettle Club mobile app
WGA, Uline Green SJ, '95 Red M/T, '88 Red 18", '01 Plum SSP, Patent Pending Yellow

MDurso

  • WKC Brave
  • Posts: 283
Re: Wsm 22 table
« Reply #3 on: September 18, 2017, 07:09:18 AM »
Pretty spiffy!
Inventor of things: labelers, automation, currency and counterfeit, cooking, gaming, tech industry, and medical.

JEBIV

  • WKC Ambassador
  • Posts: 10387
Re: Wsm 22 table
« Reply #4 on: September 18, 2017, 08:27:25 AM »
nice build very clever
Seeking a Black Sequoia I know I know, I'd settle for just the tabbed no leg grill

cwmfour

  • WKC Brave
  • Posts: 230
Re: Wsm 22 table
« Reply #5 on: September 19, 2017, 06:28:05 AM »
Elegantly simple.  Nicely done.

Whit

HoosierKettle

  • WKC Ambassador
  • Posts: 7354
Re: Wsm 22 table
« Reply #6 on: September 19, 2017, 07:36:48 AM »
My favorite table that I've seen so far. I'm not a fan of having the wsm up high like some I've seen. This gets the job done with total no table functionality with the added convenience of a table and a cart. Nicely done.


Sent from my iPhone using Weber Kettle Club mobile app

ABROB

  • WKC Brave
  • Posts: 274
Re: Wsm 22 table
« Reply #7 on: September 19, 2017, 01:46:35 PM »
Thanks

Staying as low as possible was my goal.  Kept the tubing as low as I could without interfering with the axle or caster wheel pins that go up into the frame.   I plan to also add back the wire shelf to set grates on, etc.  It will likely be zip tied to the frame.  It didn't come with a charcoal bucket, but I could add that back if I wanted to.

GoAnywhereJeep

  • WKC Brave
  • Posts: 310
    • My YouTube channel
Re: Wsm 22 table
« Reply #8 on: September 21, 2017, 03:35:32 PM »
This is awesome. I have been thinking to do the same or similar.

Pimping my own thread here to a degree but if you take a look at the DIY temp controller that I just posted in this forum, I think that would fit nicely in the spot above the tool hanger. If you can cut a 70.5mm x 28.5mm rectangle into the front panel, then you can easily mount the WILLHI 7016 in there.
YouTube channels: GringoBBQ & RubiconFI