Weber Kettle Club Forums

Grill Talk => Weber Kettle Forum => Topic started by: Golly on October 08, 2013, 11:00:40 AM

Title: RANCH KETTLE ROTISSERIE
Post by: Golly on October 08, 2013, 11:00:40 AM
hogsy and I are going to make a roti ring for the Ranch Kettle(RK)
We want to be able to do whole pig and lamb on it. We will be restricted to the size of the animal as the RK is only 93cm in diameter
Where not sure what height to make the ring
We will be making it out of 1.6mm mild steel and were going to use the same dimensions as the 57cm kettle roti ring which is 160mm
Will this be high enough??
Title: Re: RK ROTI
Post by: Golly on October 08, 2013, 01:42:41 PM
From the clip you sent me yesterday I scaled the size of the pig in relation to the wine glass on the table next to the pig
It was about 200 mm high (both the pig and the glass
So say 160 mm ring then step down of the bar say 30 mm
Still doesn't change much if the roti rod is at or near the top
I'd be inclined to keep the 160mm ring and lower the roti rod deeper into the ring
There brings another issue on sealing??
Ahh fuck nose lets just wing it
I say get the 160 mm ring ( still use lid bale /slide aside )
Mount the roti rod at the std height and then get the pig to suit
The max length - a nominal amount say 150mm
To garunteee clearance
Title: Re: RK ROTI
Post by: kendoll on October 08, 2013, 02:04:00 PM
Can't wait to see this roti monster!

Ken
Title: Re: RK ROTI
Post by: Hogsy on October 08, 2013, 02:35:49 PM
Ok 160mm/5.5in it is then
Title: Re: RK ROTI
Post by: kendoll on October 08, 2013, 02:40:49 PM
Hey Joel, seriously, it is time to change the first line of your signature. ;D

Ken
Title: RK ROTI
Post by: Peaspurple on October 08, 2013, 03:20:02 PM
I'm going to follow this closely. I look forward to seeing this baby in action.
Title: Re: RK ROTI
Post by: Hogsy on October 08, 2013, 04:54:57 PM
Quote from: kendoll on October 08, 2013, 02:40:49 PM
Hey Joel, seriously, it is time to change the first line of your signature. ;D

Ken
Maybe I'll change it on Sunday when I pick up one of my grails
Until then I'm still in denial about being that creepy guy
Title: Re: RK ROTI
Post by: kendoll on October 08, 2013, 05:03:16 PM
Quote from: Hogsy on October 08, 2013, 04:54:57 PM
Quote from: kendoll on October 08, 2013, 02:40:49 PM
Hey Joel, seriously, it is time to change the first line of your signature. ;D

Ken
Maybe I'll change it on Sunday when I pick up one of my grails
Until then I'm still in denial about being that creepy guy

Its okay Joel, i don't think you are creepy (does that sound creepy?). :)

Is that the 26er?

Ken
Title: Re: RK ROTI
Post by: Duke on October 08, 2013, 05:35:15 PM
I think these are more like Santa Maria styles that raise and lower the grate.

(http://img198.imageshack.us/img198/5741/8mdc.jpg) (http://img198.imageshack.us/i/8mdc.jpg/)

Have you thought about just making a stand alone spit that straddles the ranch kettle? Back in the day, the Weber demonstrators used to do pigs on RK's all the time.

This should encourage you guys.

http://www.weber.com/about/a-lu-lu-of-a-luau

(http://img18.imageshack.us/img18/2290/s8gc.png) (http://img18.imageshack.us/i/s8gc.png/)


A Lu-Lu of a Luau

In the late 1960s, the Boeing 747 opened up nonstop travel to Hawaii from many US mainland cities. United Airlines was the first to offer nonstop flights from Chicago, and by 1968, Chicago was besieged with TV ads extolling the exotic wonders of our fiftieth state.

At Weber we came up with a joint promotion that would ride on the coattails of United's advertising. At our key retail outlets we would hold in-store luaus, featuring grill-roasted whole pigs, United Airline coupons, and Hawaiian dancing girls. United even threw in Hawaiian orchids for the first 100 women to show up, along with posters of island sights and native dancers.

My colleagues and I donned Hawaiian shirts and shorts and generally looked completely out of place roasting pigs on giant Weber Ranch kettles in store parking lots, but the promotions were a hit. The melodic strains of the greatest ukulele hit of all time, "Tiny Bubbles", and the aroma of roasting pork would lure shoppers over, where they'd see the crazy Weber folks dressed like Don Ho and handing out free eats. What a way to make a living!

Believe it or not, these events were extremely popular among retailers, because they really drew customers and racked up sales of Weber grills. By the early 1970s, we were hosting hundreds of luaus around the country.

For me, the most memorable one took place in St. Louis at a Famous & Barr store, but I wasn't even scheduled to work the event. It all started when a fellow Weber fan called me at home one night. In a sheepish yet somewhat inebriated voice, he explained that he and his coworker were pigless. You see, it's not easy to fly into a town and find a butcher shop that just happens to have a whole pig on hand. So we had contracted with Meeske's Meat Shop in Mt. Prospect, Illinois, to prepare and box whole pigs for us. Our grill teams would pick them up on their way to the airport and check them with their luggage to their luau destination.

So, late one Friday night in 1971, I find out that both of my fellow pig roasters thought the other had picked up the pig. Braniff Airlines was serving free booze all the way to St. Louis and it wasn't until they happily landed (and I do mean happily) that they discovered neither of them had the pig. Frantic, they had called all over St. Louis and, to their dismay, were unable to find a whole pig. The big luau was scheduled to start the next day at 11:00 a.m.

We quickly hatched the following plan. I would pick up their pig, head to O'Hare, buy a ticket, check the pig, but not actually get on the flight. They would then retrieve the pig from baggage claim in St. Louis and race to the luau.

The only problem was that, among all the airlines, there was only one seat left—in first class. It departed Chicago at 9:00 a.m. on Saturday, arriving in St. Louis at 9:50 a.m. It was cutting it close, but we could still have the pig on the grill before the first notes of "Tiny Bubbles". Our mission was all the more critical because the president of Famous & Barr stores was to be there. He had said that if he liked what he saw, he would place our products in his entire chain of stores.

When Saturday dawned, I was camped out at Meeske's, waiting for the doors to open. Unfortunately, the night before was Grandpa and Grandma Meeske's 50th anniversary party and the whole family was moving rather slow and about fifteen minutes behind schedule. I was out of there with my boxed pig by 8:20 a.m., but now I had a 20-minute ride to O'Hare.

Several red lights and a slow-moving freight train later, I realized it was too close to departure time to check my luggage, so I had to go to plan B. Fortunately, I had a good-sized duffle bag in the trunk of my car.

Luckily, I found a parking spot close to the terminal. People looked at me strangely as I removed a plastic-wrapped, nearly frozen pig from a Meeske's box and stuffed it into a duffle bag, but anything can happen at O'Hare, so they just walked past another crazy. I raced to the ticket counter, lugging my pig. The agent told me I'd have to run to make the flight. Let me tell you, a pig gets mighty heavy when you're sprinting with it through an airport.

I made the flight just as the door was closing and found that the seat next to mine was a no-show. What a relief. I literally needed to hog some stowage space! I stuffed my duffled companion below the two seats in front of me. As I caught my breath and the plane gained altitude, I contemplated asking the flight attendant for one of those little wing pins for my pig, but I decided not to press my luck.

The good news was that the pig beat the president to the luau. He arrived very pleased with the size of the crowd, and complemented us on the food. "Well," I told him, as my hungover colleagues choked back their laughter, "at Weber we like to do everything in a first-class manner."
Title: Re: RK ROTI
Post by: Duke on October 09, 2013, 05:17:03 AM
After rereading this story a couple of things don't jive. One is that he was going to send the pig and not go himself. The other is, how do you cook a whole pig, even a small one like this in two hours? He said the plane landed at 9:20 and the event began at 11. What time was the food being served? I would think at high heat you would need at least six hours and it still needs to be prepared.
Title: Re: RK ROTI
Post by: G$ on October 09, 2013, 06:36:42 AM
Maybe the pig needed to start at 11:00 for an evening dinner at a day long event?

But yeah, time fogs the memory a bit.
Title: Re: RK ROTI
Post by: Golly on October 11, 2013, 02:19:32 PM
(http://i801.photobucket.com/albums/yy294/xygswagon/3D2F5099-AFF6-444A-98D4-DA17ECE82426-340-0000004C0796ECBA_zps2fdcc40c.jpg)
Title: Re: RK ROTI
Post by: Duke on October 11, 2013, 02:22:10 PM
Will this be the Roti Ring or just something to raise the lid and make it roomier? This is gonna be Jo Cool! 8)
Title: RK ROTI
Post by: Bbqmiller on October 11, 2013, 02:27:17 PM
I can't wait to see this. I have been perusing several metal fabricators near me. I have been thinking of using my CB roti ring as a template for a RK ring. I already have a motor that can spin a pig.
Title: Re: RK ROTI
Post by: Hogsy on October 12, 2013, 02:06:53 AM
The first fitting....,.
(http://i1165.photobucket.com/albums/q585/joelhogston/C1E5FFB1-1C46-47DD-B5A9-E0A818C2E0D7-8843-00000CA00E85CC97_zpsecf78049.jpg)
Fits Like a finger in a bum!!!
Title: RK ROTI
Post by: Chasing_smoke on October 12, 2013, 03:02:33 AM
That looks awesome! Incredible job!
Title: RK ROTI
Post by: Bbqmiller on October 12, 2013, 03:10:10 AM
Looking good - what kind of motor are you planning for this setup.
Title: Re: RK ROTI
Post by: JayCee on October 12, 2013, 05:16:16 AM
Saw this in the flesh today (so to speak). The workmanship on this is amazing. Top quality job.
Title: Re: RK ROTI
Post by: Hogsy on October 12, 2013, 05:37:02 AM
Quote from: Bbqmiller on October 12, 2013, 03:10:10 AM
Looking good - what kind of motor are you planning for this setup.
Not sure of the brand but there's a local guy who makes up large SS spits, who will sell the motor , shaft, forks and mounting brackets for a 90lb spit at a decent price , not as cheap as eBay but at least we'll be sure it fits
Any suggestions are welcome
Title: Re: RK ROTI
Post by: pbe gummi bear on October 12, 2013, 07:32:46 AM
Very cool. It looks like a giant macarons. Mmmm I love macarons
Title: Re: RK ROTI
Post by: Duke on October 12, 2013, 07:41:57 AM
This thread is getting cooler everytime I open it! Go Golly and Hogsy! This cook is going to be epic! ;D
Title: Re: RK ROTI
Post by: pbe gummi bear on October 23, 2013, 09:53:08 AM
Any updates?
Title: Re: RK ROTI
Post by: Hogsy on October 23, 2013, 11:37:05 AM
All will be revealed tomorrow 8)
Title: Re: RK ROTI
Post by: Duke on October 23, 2013, 01:33:58 PM
I am really excited about this. I believe this twisted pig will turn out excellent based on the cover and offset radiated heat. I bet it's going to come out like one of those spit roasted crispy chickens.
Title: Re: RK ROTI
Post by: dazzo on October 23, 2013, 03:06:19 PM
This thing is gonna be something!

"Fits like a finger in a ... "
"... in the flesh"

Cool, I'm really picking up on the Aussie lingo.
We are talking about kettles, right? 
:o
;D ;D ;D ;D

Title: Re: RK ROTI
Post by: Golly on October 23, 2013, 04:14:24 PM
Even I'm excited and I know what's being revealed
Hey hog you gunna polish the ring before the pics :o
Title: Re: Re: RK ROTI
Post by: esq3585 on October 23, 2013, 04:25:22 PM
Lol ^

Sent from my GT-I9300 using Tapatalk

Title: Re: RK ROTI
Post by: fedex on October 23, 2013, 04:43:09 PM
That looks like a good start but I like the height of the ones in the article.  Check out this website

www.onegrill.com/Motor_Bracket_for_Weber_Grills_p/4pb18.htm
Title: Re: RK ROTI
Post by: Hogsy on October 24, 2013, 09:30:15 PM
(http://i1165.photobucket.com/albums/q585/joelhogston/3E08C9FC-F9EE-4319-AB91-4E81ED9906C6-2212-000002F8D0CE95F3_zpsabe0d778.jpg)
Title: Re: RK ROTI
Post by: pbe gummi bear on October 24, 2013, 09:36:22 PM
(https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-frc3/1400446_10100155085000218_1898993322_o.jpg)
Title: Re: RK ROTI
Post by: Golly on October 24, 2013, 11:25:39 PM
Just left this with hogsy to photograph a completed setup
It took a few beers to finish off on this beautiful spring day
This thing is epic
Title: RANCH KETTLE ROTISSERIE
Post by: greeny03 on October 25, 2013, 12:10:51 AM
Now an action shot. Lamb or Pork?
Title: RANCH KETTLE ROTISSERIE
Post by: greeny03 on October 25, 2013, 12:11:23 AM
Now an action shot. Lamb or Pork?
Title: RANCH KETTLE ROTISSERIE
Post by: greeny03 on October 25, 2013, 12:11:56 AM
Now an action shot. Lamb or Pork?
Title: RANCH KETTLE ROTISSERIE
Post by: greeny03 on October 25, 2013, 12:12:28 AM
Now an action shot. Lamb or Pork?
Title: Re: Re: RK ROTI
Post by: Jocool on October 25, 2013, 12:31:56 AM
Quote from: Hogsy on October 24, 2013, 09:30:15 PM
(http://i1165.photobucket.com/albums/q585/joelhogston/3E08C9FC-F9EE-4319-AB91-4E81ED9906C6-2212-000002F8D0CE95F3_zpsabe0d778.jpg)
Peekaboo!

Sent from another Galaxy using Mental Telepathy.

Title: Re: Re: RK ROTI
Post by: Jocool on October 25, 2013, 12:34:43 AM
Quote from: Hogsy on October 24, 2013, 09:30:15 PM
(http://i1165.photobucket.com/albums/q585/joelhogston/3E08C9FC-F9EE-4319-AB91-4E81ED9906C6-2212-000002F8D0CE95F3_zpsabe0d778.jpg)
Peekaboo!

Sent from another Galaxy using Mental Telepathy.

Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on October 25, 2013, 01:52:17 AM
Ok, it's finally finished and ready to go
Be warned Brian 'Pic Heavy' ;D
This was fun to build and all of Golly's and my resources were pulled in to achieve
The Workshop
(http://i1165.photobucket.com/albums/q585/joelhogston/C6FA3DDE-DB9B-4611-9408-10B525E9DDED-2305-00000309A424A756_zps8b9d5a8e.jpg)
You have all seen the ring so I'll start with the mounting brackets for the shaft and the motor . The shaft sits on the bearings instead of on the slots in the ring. Makes for some smooth roti action.
(http://i1165.photobucket.com/albums/q585/joelhogston/6E7215ED-8525-4AB8-83E1-E8BF530522EC-2305-00000308BA509A88_zps4ec7b79e.jpg)
(http://i1165.photobucket.com/albums/q585/joelhogston/F8403B9C-3887-41FF-98AF-E012B057DA32-2305-00000308FE71C1B0_zps2f6b47fd.jpg)
(http://i1165.photobucket.com/albums/q585/joelhogston/4FEE46D4-7D18-4060-9C7F-F36C4FF9C5F8-2305-0000030909F2A7A0_zpsbb81b81c.jpg)
The motor, the most expensive part..... So far! Fully encased with SS and ready to turn
It weighs about 8lbs and can turn up to 90lbs.... Over kill... Yeah but we believe do it once do it right
Once the motor was mounted we noticed the weight started to lift the ring slightly so we made another mod, also the motor is attached to the bracket by bolts and wing nuts for easy removal
(http://i1165.photobucket.com/albums/q585/joelhogston/9266B6AD-4FF1-4BD1-BC87-16C0D5618999-2305-0000030896DFA7E3_zpsa4a7e4e9.jpg)
(http://i1165.photobucket.com/albums/q585/joelhogston/C9BA10B1-A1B9-4D25-A1CB-29B6FD107E04-2305-000003088D73E07C_zps090d01f8.jpg)
Now the shaft and forks, its 1 inch SS rod with 4 prongs, we should be able to get 4 decent cuts of meat on it

(http://i1165.photobucket.com/albums/q585/joelhogston/97971EC3-6F95-4195-91B9-04CBD69FCD8A-2305-0000030882EA7804_zpsff648b88.jpg)
(http://i1165.photobucket.com/albums/q585/joelhogston/103EFD14-5120-499F-9716-4FC23EED4BDD-2305-0000030874CA85D2_zps385d6f81.jpg)
We used sockets to connect the shaft to the motor
(http://i1165.photobucket.com/albums/q585/joelhogston/2D306776-4E5C-43C1-BA16-7B2A63112973-2305-000003091B6B0795_zps355b8986.jpg)
(http://i1165.photobucket.com/albums/q585/joelhogston/A24A34A0-7A78-4385-ADB4-12940CD3C1AF-2385-0000033AFB677877_zps8092ee7c.jpg)
The cooking set up
We cut some expanded to size for general grilling
(http://i1165.photobucket.com/albums/q585/joelhogston/382FDDF2-FEC2-4FF2-B7C2-A01CE1F7BF35-2305-00000308AD0476CE_zpsa16372e2.jpg)
And made up some baskets out of an old kettle,expanded and some SS
Not the prettiest but it will do the job
Each basket holds over 2 chimneys worth of charcoal
(http://i1165.photobucket.com/albums/q585/joelhogston/2A0D35D1-BF91-4098-8BB1-5457ED278451-2305-00000308A2FCBFA5_zps9ce2c777.jpg)
(http://i1165.photobucket.com/albums/q585/joelhogston/3D9DB7E0-B35A-409F-BE4E-9699FD56642A-2305-00000308656F48D0_zps8a152927.jpg)
All that's left now is to try it out, 30lb pig has been ordered and as long as the total fire ban which has been running for a fortnight is lifted, we'll be cooking on it next Friday night
Title: RANCH KETTLE ROTISSERIE
Post by: Bbqmiller on October 25, 2013, 02:12:17 AM
That is a well designed piece of equipment and I really like the shaft bearings on both ends. Will definitely cut down on friction with a large load on the spit. Also love the baskets, nice use of materials. Overall great job!!!!! Can't wait to see the hog spinning!
Title: Re: RANCH KETTLE ROTISSERIE
Post by: JayCee on October 25, 2013, 02:18:53 AM
Awesome work guys! Job came out amazing. Think we might have to get another WKC Aussie chapter meeting going and crank this bad boy up!
Title: Re: RANCH KETTLE ROTISSERIE
Post by: saxart on October 25, 2013, 02:28:32 AM
AMAZING...
Title: Re: RANCH KETTLE ROTISSERIE
Post by: MartyG on October 25, 2013, 02:30:27 AM
That thing is built like a carnival ride! Should last a few hundred years, give or take. Can't wait to see it in action, but pics won't do, we need video.
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Jocool on October 25, 2013, 03:07:47 AM
OMG.... You uni-jointed it? :o

That's grouse! (another new Aussie word)
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Jeff on October 25, 2013, 04:15:03 AM
wow, what nice work.  It looks so professional.   When do we get to see photos of it in action????
Title: Re: RANCH KETTLE ROTISSERIE
Post by: OoPEZoO on October 25, 2013, 04:19:50 AM
Quote from: Hogsy on October 25, 2013, 01:52:17 AM
Each basket holds over 2 chimneys worth of charcoal

Holy Shat.....thats awesome  ;D
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Thin Blue Smoke on October 25, 2013, 04:26:23 AM
IMPRESSIVE!  The baskets are a really cool addition.  I agree, there definately needs to be video for the first use.
Title: Re: RANCH KETTLE ROTISSERIE
Post by: HankB on October 25, 2013, 05:10:43 AM
That ring is a thing of beauty! Why do you think it is limited to 90 lb? Did you mean 90 Kg? I think it could! I like the attention to detail such as the flex joint to the motor and the rollers for the spit. I would like to humbly submit some further suggestions.

For the balance problem with the motor, I would mount a surface toggle clamp (http://www.amazon.com/TruePower-Horizontal-Quick-Release-Surface-Toggle/dp/B009KB9F38) to the opposite side of the ring to snub it to the bowl. It only needs to be there before/after you put the food on.

(http://ecx.images-amazon.com/images/I/31G5aZIleGL.jpg)

I think that would be a better solution than an independent brace to the floor. You would need to find one with a heat proof tip.

The other thing I would do (if not already planned) is provide some accommodation for an adjustable counter weight to balance the load when you cannot easily spit through the center of gravity. I didn't need that with two birds on my spit but I did phase them 180° apart. With a large turkey I might need to employ a counter weight.

I hope they lift your burn ban so you can fire that baby up! I know how eager you must be (http://weberkettleclub.com/forums/food-pr0n/dinner-might-be-a-liitle-late/) to do that!
Title: Re: RANCH KETTLE ROTISSERIE
Post by: MaxBobcat on October 25, 2013, 06:02:35 AM
very nice.  everything looks built very well.  fantastic!
Title: Re: RANCH KETTLE ROTISSERIE
Post by: glrasmussen on October 25, 2013, 06:19:41 AM
Just awesome!!! Congrats on super build gents!
Title: Re: RANCH KETTLE ROTISSERIE
Post by: pbe gummi bear on October 25, 2013, 07:19:21 AM
That's so awesome. Very well constructed and engineered.
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Duke on October 25, 2013, 09:13:21 AM
I'm Chuffed! :o

That is the BMF! 8)
Title: Re: RK ROTI
Post by: dazzo on October 25, 2013, 10:31:26 AM
Quote from: dazzo on October 23, 2013, 03:06:19 PM
This thing is gonna be something!

And it is!

Title: Re: RANCH KETTLE ROTISSERIE
Post by: pbe gummi bear on October 25, 2013, 10:36:36 AM
Hey, you can create a small hook that fastens to the ring and an existing hole on the bottom bowl so that the motor doesn't tilt it out. it would look completely stealth on the outside and not intrusive for normal cooking. and cheap!
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on October 25, 2013, 12:37:34 PM
Thanks everyone for the positive replies, it's these reactions that keep the motivation up when trying to complete projects
As far as the brace goes , thanks for the suggestions and I'll try and explain a little better what happens when the motor is attached with out the brace.
When attached and the lid is off it doesn't lift the opposite side where the shaft runs through the ring
The top of the ring tends to roll out and the bottom push in at 2 points, say if the motor end of the ring is north and the other end of the shaft is south the ring has pull on it at east & west
Now it's not all that critical, it won't pop out of position and really the only way you can notice it is the motor doesn't look level
I can push down on the shaft end as hard as I want and it won't make any difference
And once the lid is on the sides of the ring pull in and the motor sits back up level
I think the combination of cutting slots for the shaft and having 8lbs hanging a foot off the side of the ring is the issue. The brace was a nice easy fix. Once the motor is supported problem solved plus it's just a nut and bolt attaching it that can easily removed but I guess it does lose a bit of sleekness with the brace
As far as the motor Hank, it's rated to turn 40kg or 90lbs and I don't think your going to get much more meat than that inside the ranch
Title: Re: RANCH KETTLE ROTISSERIE
Post by: AZ_MIKEY on October 25, 2013, 12:59:10 PM
What type of metal is the ring and motor mounting plate made of. I know at the beginning of the thread the talk was mild steel. I was wondering if you kept with that or went all stainless. I ask cause the pics from what I can tell where the mount is welded to the ring looks like stainless.
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on October 25, 2013, 01:02:40 PM
Your right Mikey , all SS
Title: Re: RANCH KETTLE ROTISSERIE
Post by: AZ_MIKEY on October 25, 2013, 01:13:20 PM
In that case where it is welded I noticed what some welders/fitters refer to as burn through or sugaring on the backsides of the welds. When this happens on mild steel nothing to worry about really, but on stainless it becomes an area where rust can occur. The fix that can be performed is grind out the burn through and weld over it with high nickel low carbon filler rod. The burn through cause what little carbon there is in stainless to collect in one area. The low amount or absence of carbon in stainless is what keeps it from rusting. Or you can simply grind the burn through even and put and acid paste on it to neutralize it to a point that it won't as easily rust.
Title: Re: RANCH KETTLE ROTISSERIE
Post by: AZ_MIKEY on October 25, 2013, 01:17:11 PM
When stainless welds are made the weld bead or chevrons should be a silver to gold coloring with very little blue and preferably no black coloring. This means no contamination got into the weld. Burn through shows up black on the back side of the weld due to no gas shield being there to shield out gasess that are naturally in the air around us.
Title: Re: RANCH KETTLE ROTISSERIE
Post by: pbe gummi bear on October 25, 2013, 01:37:44 PM
MIKEY, I was at a trade show last week and I saw a product that cleaned up the weld discoloration. The rep also mentioned that it recoated that portion so that it doesnt rust. Is there validity to this or was it sales bs?
Title: RANCH KETTLE ROTISSERIE
Post by: Bbqmiller on October 25, 2013, 01:38:31 PM
Can you post some measurements on the baskets?
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on October 25, 2013, 02:12:45 PM
Mikey thanks for the tips
Once the ring has a coating of pig/lamb/beef/chicken fat on it which should be next weekend, will rust still be an issue? Also the Kettle and ring will always be under cover and we are getting a cover made up for it so I was thinking rust wouldn't be an issue
Quote from: Bbqmiller on October 25, 2013, 01:38:31 PM
Can you post some measurements on the baskets?
The baskets are about 28 inches long and 9 inches wide, they were made to suit the contour of the bowl. The grate can also be lifted in and out of the kettle with the ring still in place
Title: Re: RANCH KETTLE ROTISSERIE
Post by: AZ_MIKEY on October 25, 2013, 04:42:20 PM
"Mikey thanks for the tips
Once the ring has a coating of pig/lamb/beef/chicken fat on it which should be next weekend, will rust still be an issue? Also the Kettle and ring will always be under cover and we are getting a cover made up for it so I was thinking rust wouldn't be an issue"

Hogsy, the problem with burn through/sugaring of a weld isn't just limited to rust it is also a place for bacteria to growand stay harbored. Not such a big deal on a piece that gets hot frequently but something that when it cools down and stays at temps below a tempature that can kill said bacteria it can become a problem. As far as the rust concern the best thing is to keep an eye on it and pretty much treat areas where it can happen I.e. the burn through areas like you would on an area of any kettle that is open to the elements and no longer has porcelain covering it. Also just watch the stainless around that area that if rust appears you take care of it immediately as it will move and impregnate the rest of the stainless. My minimum suggestion is go to a fan shop or metal working/ supply store and get some of the acid paste to put o. The burn through spots and treat it from time to time. But I will leave it at keep an eye on those spots and above all enjoy that frwaking bad ass set up! And congrats on having the cajones to tackle such a project.
Title: Re: RANCH KETTLE ROTISSERIE
Post by: AZ_MIKEY on October 25, 2013, 04:56:53 PM
Quote from: pbe gummi bear on October 25, 2013, 01:37:44 PM
MIKEY, I was at a trade show last week and I saw a product that cleaned up the weld discoloration. The rep also mentioned that it recoated that portion so that it doesnt rust. Is there validity to this or was it sales bs?

Gummi, was this product solely for stainless steel welds or more of and all around product for all metals or even something that might have been marketed for tig produced welds or aluminium and stainless. As far as I know there really isn't a fix that lasts that takes care of burn through as far as taking care of the color on stainless welds as long as there is no burn through you can buff them out in many ways. One while they are still hot scrub them with a stainless wire brush. 2 let them cool and grind/ blend them in with a zircon type disc( usually a flap style) or use a red med croase scotchbrite style buffing wheel or hand pad. 3 let them cool use acid paste and then wash of acid paste. All ways produce different levels and qualities than the other in regards to lusters and shines and overall appearances. If you want to see the weld bead with the chervons going tthe route of the weld is still hot with a wire brush produces a very beautiful look when the weld is between that silver to gold color as it will clean the weld to exactly the same color as and shine as the metal being bonded together. Also what type of filler rod used plays some part in it. So many variables.
Title: Re: RANCH KETTLE ROTISSERIE
Post by: pbe gummi bear on October 25, 2013, 05:06:44 PM
Quote from: AZ_MIKEY on October 25, 2013, 04:56:53 PM
Quote from: pbe gummi bear on October 25, 2013, 01:37:44 PM
MIKEY, I was at a trade show last week and I saw a product that cleaned up the weld discoloration. The rep also mentioned that it recoated that portion so that it doesnt rust. Is there validity to this or was it sales bs?

Gummi, was this product solely for stainless steel welds or more of and all around product for all metals or even something that might have been marketed for tig produced welds or aluminium and stainless. As far as I know there really isn't a fix that lasts that takes care of burn through as far as taking care of the color on stainless welds as long as there is no burn through you can buff them out in many ways. One while they are still hot scrub them with a stainless wire brush. 2 let them cool and grind/ blend them in with a zircon type disc( usually a flap style) or use a red med croase scotchbrite style buffing wheel or hand pad. 3 let them cool use acid paste and then wash of acid paste. All ways produce different levels and qualities than the other in regards to lusters and shines and overall appearances. If you want to see the weld bead with the chervons going tthe route of the weld is still hot with a wire brush produces a very beautiful look when the weld is between that silver to gold color as it will clean the weld to exactly the same color as and shine as the metal being bonded together. Also what type of filler rod used plays some part in it. So many variables.

I have no idea, but thanks for the info. This liquid was some of the stuff I saw, but there were other vendors too. http://cyndan.com.au/en/specialised-cleaners/68-pickle-it-liquid-all-metals-welding-stain-remover.html
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Golly on October 25, 2013, 07:10:53 PM
Quote from: Hogsy on October 25, 2013, 12:37:34 PM
Thanks everyone for the positive replies, it's these reactions that keep the motivation up when trying to complete projects
As far as the brace goes , thanks for the suggestions and I'll try and explain a little better what happens when the motor is attached with out the brace.
When attached and the lid is off it doesn't lift the opposite side where the shaft runs through the ring
The top of the ring tends to roll out and the bottom push in at 2 points, say if the motor end of the ring is north and the other end of the shaft is south the ring has pull on it at east & west
Now it's not all that critical, it won't pop out of position and really the only way you can notice it is the motor doesn't look level
I can push down on the shaft end as hard as I want and it won't make any difference
And once the lid is on the sides of the ring pull in and the motor sits back up level
I think the combination of cutting slots for the shaft and having 8lbs hanging a foot off the side of the ring is the issue. The brace was a nice easy fix. Once the motor is supported problem solved plus it's just a nut and bolt attaching it that can easily removed but I guess it does lose a bit of sleekness with the brace
As far as the motor Hank, it's rated to turn 40kg or 90lbs and I don't think your going to get much more meat than that inside the ranch



Well said hogsy
Best solution possible to keep everything removable and mobile
Thanks for the suggestions but they wouldn't be appropriate
Title: Re: RANCH KETTLE ROTISSERIE
Post by: kendoll on October 25, 2013, 08:13:59 PM
Holy shit guys, that looks amazing. You guys must be stoked with it. I know you have put a lot of thought, time, and money in to this thing so it is great to see it ready to roll.

I hope the fire ban lifts in time for you guys to put it through its paces. I know the people you will be cooking for will appreciate it!

Can't wait to see the pics of it in action. Hopefully get to sample some of the end product myself in the not too distant future.

Ken
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Golly on October 25, 2013, 08:18:35 PM
Quote from: kendoll on October 25, 2013, 08:13:59 PM
Holy shit guys, that looks amazing. You guys must be stoked with it. I know you have put a lot of thought, time, and money in to this thing so it is great to see it ready to roll.

I hope the fire ban lifts in time for you guys to put it through its paces. I know the people you will be cooking for will appreciate it!

Can't wait to see the pics of it in action. Hopefully get to sample some of the end product myself in the not too distant future.

Ken

yes ken majorly stoked

upon the final fitment and powering up there was a high five thrown about 8) 8)
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Duke on October 25, 2013, 08:21:48 PM
Quote from: Golly on October 25, 2013, 08:18:35 PM


yes ken majorly stoked

upon the final fitment and powering up there was a high five thrown about 8) 8)

I believe the correct term is Chuffed. ;) I know I am. :D
Title: Re: RANCH KETTLE ROTISSERIE
Post by: G on October 27, 2013, 07:52:02 AM
That thing is cool...congrats on an awesome build.  Cant wait for some pics, or better yet, a video of your first "spin". 
Title: Re: RANCH KETTLE ROTISSERIE
Post by: 1buckie on October 27, 2013, 08:48:07 AM


OK.........................








..........PIG that thing UP !!!!!!!
Title: Re: RK ROTI
Post by: Hottuna on October 27, 2013, 06:20:32 PM
Looking awesome!! i  used the same roller bearing shaft support when i had my spit built up.
Maybe i missed it but are you guys going to use a counterweight on the shaft when roasting full animals? As you know they arent the most balanced cut. Saves the motor in the longrun.[img]
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on October 27, 2013, 07:17:03 PM
Wasn't going to use a counterweight but would like to see some pics of yours to get an idea of it
I don't use the counterweight on my kettle roti so don't see the point of using it on the RK  but that doesn't mean its not a good idea
Title: Re: RANCH KETTLE ROTISSERIE
Post by: salad on October 27, 2013, 09:21:07 PM
Not sure how or why I'm just finding this thread but WOW that's a nice build.  I want to watch something spinning on that thing!
Title: Re: RANCH KETTLE ROTISSERIE
Post by: louievandeoorst on October 28, 2013, 12:51:10 AM
counterweight for something so big  is just about must,
well my two cents..
mates ..good luck..
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hottuna on October 29, 2013, 03:20:29 AM
Quote from: Hogsy on October 27, 2013, 07:17:03 PM
Wasn't going to use a counterweight but would like to see some pics of yours to get an idea of it
I don't use the counterweight on my kettle roti so don't see the point of using it on the RK  but that doesn't mean its not a good idea

Our spit motor supplier recommends it
The counter weights slide onto the shaft and lock in position via a grub screw. A little weight goes a long way. Ever noticed the motor stuggles on certain angles of the spin? Full beasts are always heavier on the head, and shoulder side the motor tends to accelerate on the down stroke then struggle turning the weight uphill and so on - this is what is not good for life of the motor.
They weights are easy to knock up or i think we have a few to suit 25mm round shaft at work.  I will post a pic and exact weight tomorrow
Title: Re: RANCH KETTLE ROTISSERIE
Post by: landgraftj on October 29, 2013, 03:50:15 AM
Very impressive setup guys! Can't wait to see it in action.
Title: Re: RANCH KETTLE ROTISSERIE
Post by: LightningBoldtz on October 29, 2013, 04:56:51 AM
This really is an amazing job. 
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on October 29, 2013, 11:53:37 AM
Hottuna, thanks for the advice, I'd like to see some pics of the counterweights
I had a chat with the gentleman who sold us the motor yesterday and he said not to worry about it, he has been designing and using roti's for most of his working life and was telling me how he's even had whole cow legs , bone in, weighing 65lbs on the spit using this motor, obviously it would be very hard to balance this type of cut. Now in saying that it doesn't mean he's right and I can definetly see the benefit of using a counterweight especially for longevity of the motor. Although the motor itself was pretty cheap, it was the mounting and housing that was the expensive part.
Pics Please
Title: Re: RANCH KETTLE ROTISSERIE
Post by: pbe gummi bear on October 29, 2013, 12:04:14 PM
It's actually not just the weight of the load but the torque on the motor. Can you look at the motor bell and see what the model number or tq rating is?
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on October 29, 2013, 12:25:51 PM
I'll get back to you on that one L
ATM the RK is packed up and ready for our EOST which starts tomorrow
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hottuna on October 29, 2013, 02:18:05 PM
Here is the pic, it weighs 1.5kg - suits a 22mm round shaft,  but this can easily be changed by your spit guy, it is solid stainless steel, they are $30 inc delivery(http://i1013.photobucket.com/albums/af252/Daniel_Pipitone/counterw_zpsffd7a2b2.jpg) (http://s1013.photobucket.com/user/Daniel_Pipitone/media/counterw_zpsffd7a2b2.jpg.html)

Tell me more about where your using the ranch this weekend
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Golly on November 03, 2013, 11:28:54 PM
http://s801.photobucket.com/user/xygswagon/media/99B583F9-C3EA-400B-80EB-4EB46FA5806F-989-0000028C56BBC198_zps9d06dead.mp4.html
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hottuna on November 04, 2013, 01:58:33 AM
Nice crackling! Man that ranch rocks
im now starving after those pics! Awesome campsite too
Dan
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Duke on November 04, 2013, 09:43:46 AM
You guys and now legends! Just awesome! :o
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Golly on November 04, 2013, 10:02:02 AM


(http://i801.photobucket.com/albums/yy294/xygswagon/F390BA4E-4720-4CA7-960D-31D53D687453-989-0000027CC11E46BC_zps4ff0720d.jpg) (http://s801.photobucket.com/user/xygswagon/media/F390BA4E-4720-4CA7-960D-31D53D687453-989-0000027CC11E46BC_zps4ff0720d.jpg.html)

(http://i801.photobucket.com/albums/yy294/xygswagon/43BFC7FC-CF22-4E1B-A927-27D0C2DC4E2C-989-0000027CCE1EB819_zps0a9c9384.jpg) (http://s801.photobucket.com/user/xygswagon/media/43BFC7FC-CF22-4E1B-A927-27D0C2DC4E2C-989-0000027CCE1EB819_zps0a9c9384.jpg.html)

(http://i801.photobucket.com/albums/yy294/xygswagon/52BC08E6-A457-4AF5-A41F-A225BE9AB85F-989-0000027CD3C406B2_zpsa5cb8b98.jpg) (http://s801.photobucket.com/user/xygswagon/media/52BC08E6-A457-4AF5-A41F-A225BE9AB85F-989-0000027CD3C406B2_zpsa5cb8b98.jpg.html)

(http://i801.photobucket.com/albums/yy294/xygswagon/D0C7BEB5-F5F9-4339-B315-4B4A37B50DD8-989-0000027CD9F71A11_zps40f9c34b.jpg) (http://s801.photobucket.com/user/xygswagon/media/D0C7BEB5-F5F9-4339-B315-4B4A37B50DD8-989-0000027CD9F71A11_zps40f9c34b.jpg.html)

(http://i801.photobucket.com/albums/yy294/xygswagon/098368BD-738A-41EB-85DC-C033D198B298-989-0000027CF6C96A15_zps279924cb.jpg) (http://s801.photobucket.com/user/xygswagon/media/098368BD-738A-41EB-85DC-C033D198B298-989-0000027CF6C96A15_zps279924cb.jpg.html)
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Golly on November 04, 2013, 10:03:00 AM
http://s801.photobucket.com/user/xygswagon/media/B63CD1FE-FE87-4950-B941-9D321D45F82C-989-0000028B4615E123_zpse3548154.mp4.html
Title: Re: RANCH KETTLE ROTISSERIE
Post by: kendoll on November 04, 2013, 12:44:09 PM
OMG! I bet that smelled amazing! Really just a fantastic effort guys.

You know you are going to be asked to do this at the next WKC meet up. The neighbours will lose their minds!

Ken
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Duke on November 04, 2013, 01:18:51 PM
Great photos and teamwork! Epic cook, definitely front page material.

What's funny is in that last photo with the two of you it looks more like Butch! ;D

(http://img822.imageshack.us/img822/575/xuk3.jpg) (http://img822.imageshack.us/i/xuk3.jpg/)





Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on November 10, 2013, 01:59:06 PM
Just wanted to add a few things before I forget
The suckling pig was 15kg/33lbs
1hr spent prepping pig on the shaft
3-3.5hrs cooking at 180c/350f
10-20mins to get the skin to crackle
We set it up with 2 baskets either side of the shaft and it only took 1 chimney of lump charcoal to get it up to 180c/350f. Foiled the entire charcoal grate between the 2 baskets and used 3 disposable drip trays under the pig. We added another 2 chimneys to get the temp up to 230c/450f to crackle but indirect didn't seem to make any difference to the skin after 1/2 hr. So we dropped it back to 180c/350f for the rest of the cook.
We used the Thermapen to check temps after 3hrs and it was ready to go
We then moved some of the coals directly underneath the pig and it crackled up Very quickly! Lid was off for this part
It was just a matter of moving the coals to different parts of the pig to form the crackle
Best part was we were playing cricket about 1/2 mile away and could smell the pig roasting away.... And boy did it smell good
The 10 chickens we cooked the night before were pretty amazing too
Just some oil and Mad Hunky hot ass whangs seasoning
Chicken was moist and juicy and the skin was super crispy
Chicken furthest from the charcoal seemed to brown up quicker than those next to the charcoal
We used one basket with two chimneys worth of lit charcoal
It was a total success and a lot of the guys with us helped out and enjoyed the process
I think we have a few charcoal converts
I think this size pig is probably maximum size for the setup. Which is fine because the meat on a suckling pig is much more juicier and flavour some than a large pig IMHO
Next up will be a lamb

Title: Re: RANCH KETTLE ROTISSERIE
Post by: mwmac on November 11, 2013, 07:46:44 AM
Simply amazing...well done!
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on October 02, 2014, 02:31:32 AM
We had the final piece made up for the ranch this week..... A drip tray
The problem we were having is catching the fat from whatever we cook to the point where the ash catcher was half full after cooking a lamb or pig, it also makes cleaning a PITA. We tried covering the charcoal grate with foil and folding up the edges and a couple of disposable drip pans but the results were average at best
So here's the new drip pan and it's a monster!!!
Because of the size we used 5mm Aluminum
(http://i1165.photobucket.com/albums/q585/joelhogston/EE63D6CB-789F-443A-A27A-8095E3C18D27_zpst5vhgvak.jpg) (http://s1165.photobucket.com/user/joelhogston/media/EE63D6CB-789F-443A-A27A-8095E3C18D27_zpst5vhgvak.jpg.html)
2 inch sides
(http://i1165.photobucket.com/albums/q585/joelhogston/187F874E-3C54-4152-BEBC-D999D7881F34_zpsiyywqusc.jpg) (http://s1165.photobucket.com/user/joelhogston/media/187F874E-3C54-4152-BEBC-D999D7881F34_zpsiyywqusc.jpg.html)
Perfect fit between the charcoal baskets
(http://i1165.photobucket.com/albums/q585/joelhogston/34A82745-602C-4C63-9FB8-91D107796548_zpskk6mkgaa.jpg) (http://s1165.photobucket.com/user/joelhogston/media/34A82745-602C-4C63-9FB8-91D107796548_zpskk6mkgaa.jpg.html)
(http://i1165.photobucket.com/albums/q585/joelhogston/77484FA7-A4BD-46CC-9ADB-7A3E2C08DB64_zpsb8yv4rmi.jpg) (http://s1165.photobucket.com/user/joelhogston/media/77484FA7-A4BD-46CC-9ADB-7A3E2C08DB64_zpsb8yv4rmi.jpg.html)
And here it is next to my 26er and 22 drip pans
(http://i1165.photobucket.com/albums/q585/joelhogston/F8CF8F93-6F06-427B-BF67-FB3863E7E70A_zpswfkm2slv.jpg) (http://s1165.photobucket.com/user/joelhogston/media/F8CF8F93-6F06-427B-BF67-FB3863E7E70A_zpswfkm2slv.jpg.html)
Title: Re: RANCH KETTLE ROTISSERIE
Post by: 1buckie on October 02, 2014, 03:24:47 AM
Just A Picture I Liked..........

(http://i1165.photobucket.com/albums/q585/joelhogston/F8CF8F93-6F06-427B-BF67-FB3863E7E70A_zpswfkm2slv.jpg) (http://s1165.photobucket.com/user/joelhogston/media/F8CF8F93-6F06-427B-BF67-FB3863E7E70A_zpswfkm2slv.jpg.html)


Good show !!!


you could even roast stuff in that,I suppose  ........ ;D
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Golly on October 02, 2014, 03:40:34 AM
We now have shares in the aluminum smelter :P
Title: Re: RANCH KETTLE ROTISSERIE
Post by: saxart on October 02, 2014, 07:15:58 AM
Hogsy-
That is fantastic!   I'm going to have to make one of these for our slow (off-set) cooks to catch the drippings.    I see that the sides are 2" tall.  How wide is it between the charcoal baskets?

(Yes, Greg...  I'll make you one too..)   ::)

Title: Re: RANCH KETTLE ROTISSERIE
Post by: SixZeroFour on October 02, 2014, 07:23:14 AM
Absolutely unreal you guys! Not only the fact that you MADE a roti for that ranch, but the quality!! ~ Fit and finish is seriously awesome.

This EPIC post deserves an honorary entry into Mod Month IMO! @MartyG ?! Technically the final unit was not completed until October right?!?  ;)

Wow.

Title: Re: RANCH KETTLE ROTISSERIE
Post by: MartyG on October 02, 2014, 07:36:20 AM
I'll have to go under the hood to make that call  ;)  Truly one of the coolest mods we've seen. The OZ-Mod Squad boyz are crazy good. I hear they built a special vehicle designed to carry around some of their amazing creations:
(https://farm3.staticflickr.com/2948/15420087782_a9ecc382af_o.jpg)
Title: Re: RANCH KETTLE ROTISSERIE
Post by: glrasmussen on October 02, 2014, 07:39:23 AM
Quote from: saxart on October 02, 2014, 07:15:58 AM
Hogsy-
That is fantastic!   I'm going to have to make one of these for our slow (off-set) cooks to catch the drippings.    I see that the sides are 2" tall.  How wide is it between the charcoal baskets?

(Yes, Greg...  I'll make you one too..)   ::)

Hogsy, outstanding. The do need this, as they are a PITA to clean after the cook.

Art, I'm waiting... ;)
Title: Re: RANCH KETTLE ROTISSERIE
Post by: jmeier64 on October 02, 2014, 07:43:22 AM
Looks great guys, very impressed at the ingenuity and craftsmanship. What Art, no love headed this way :P
Title: Re: RANCH KETTLE ROTISSERIE
Post by: saxart on October 02, 2014, 08:10:34 AM
Jim-
Get a Ranch, then we'll talk!  :)
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Winz on October 02, 2014, 08:33:12 AM
Quote from: saxart on October 02, 2014, 07:15:58 AM
Hogsy-
That is fantastic!   I'm going to have to make one of these for our slow (off-set) cooks to catch the drippings.    I see that the sides are 2" tall.  How wide is it between the charcoal baskets?

(Yes, Greg...  I'll make you one too..)   ::)

Hey Art, what does it take to get on this list?

Winz
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on October 02, 2014, 12:29:38 PM
Thanks you, I knew you guys would appreciate it.
These are really easy to make all you need is some cardboard, packing knife and some $$$
I start by tracing the curve of the charcoal grate onto some cardboard, you want to make it about an inch longer than the actual grate as the tray will be longer than the charcoal grate due to the shape of the bowl.
(http://i1165.photobucket.com/albums/q585/joelhogston/840317B3-ACFA-44DA-B667-7968E7DBB3EC_zpsfefjwdfh.jpg) (http://s1165.photobucket.com/user/joelhogston/media/840317B3-ACFA-44DA-B667-7968E7DBB3EC_zpsfefjwdfh.jpg.html)
Then fit the cardboard in the bowl on top of the charcoal grate and trim till your happy with the fit.
Set the charcoal baskets up in the kettle on top of the cardboard and mark where they fit.
Trim the cardboard to fit the baskets until your happy with the fit. This should only take about 10mins
(http://i1165.photobucket.com/albums/q585/joelhogston/3324F229-A431-4E8F-AD41-4040410390D7_zps5m0gkacv.jpg) (http://s1165.photobucket.com/user/joelhogston/media/3324F229-A431-4E8F-AD41-4040410390D7_zps5m0gkacv.jpg.html)
I then take the template to a fabricator/welder and get them to make it.
The sides only need to be an inch high for a 22 kettle
(http://i1165.photobucket.com/albums/q585/joelhogston/3A7064B9-A6D0-40E8-84EB-E10483D2D992_zps697wzfgr.jpg) (http://s1165.photobucket.com/user/joelhogston/media/3A7064B9-A6D0-40E8-84EB-E10483D2D992_zps697wzfgr.jpg.html)
Just make sure you cover in foil when cooking it makes an easy cleanup when your finished
Title: Re: RANCH KETTLE ROTISSERIE
Post by: saxart on October 02, 2014, 03:16:16 PM
Hogsy-
Great write-up with the cardboard on a standard kettle.   Mind if I ask how wide the Ranch version is between the homemade charcoal baskets?
Title: Re: RANCH KETTLE ROTISSERIE
Post by: Hogsy on October 02, 2014, 04:01:33 PM
Thanks Sax, for memory it's 450-500mm wide(not sure what it is in imperial)
Title: Re: RANCH KETTLE ROTISSERIE
Post by: saxart on October 02, 2014, 07:19:37 PM
Thanks Hogsy.  That converts to be about 20 inches imperial.   Now that I looked through some of the earlier posts, I see that the charcoal baskets are "approx. 9" wide", so that math works on a 31.5" charcoal grate.

Thanks a bunch!
Title: Re: RANCH KETTLE ROTISSERIE
Post by: northernQ on January 18, 2018, 04:12:48 PM
Instead of pictures I get an image that says "please update your account to enable 3rd party hosting"

Are these pictures anywhere else on the web?
I have s Ranch kettle and would like to do the same build.

Thanks


Sent from my iPhone using Weber Kettle Club mobile app (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)