Hey y'all,
Happy Friday! So I have been working on a solution to fix torn off / rusted through old handles, eliminating new taco handles, using old wood single or double screw, and no exposed hardware. Here's the solution. What do you think?
In search of Imperial and The Custom.
I like it
Really like it how's you do it?
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Those straps look pretty good. I would recommend using 1.25" washers on the top with some kind of gasket material between the washer and lid. Also, I use a 1.25" washer on the bottom, but you need to take a ball peen hammer to the hole so it doesn't crunch on the lip of the hole inside the kettle. This gives the bottom washer a kind of cone shape that only touches on the outside edge when installed. SS hardware is what I use as well. They might stick out more though without the shield. My washers aren't as noticeable with the shield in place.
I am hoping that with the larger washers the porcelain holds up a little better around the handle holes.
Quote from: blu082003 on August 28, 2020, 08:55:16 PM
Really like it how's you do it?
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
[mention]blu082003 [/mention] Measured up an old handle from the wood handle era, laser cut from stainless steel, formed in a press and plug welded stainless studs in a tapped hole. Grind and polish weld off and it looks like it's welded on. The whole part is made of stainless. If you wanted to paint to match, that can be done as well, but since the taco grills were stainless, I opted to leave unpainted.
Sent from my iPhone using Tapatalk
Stunning
Sent from my SM-N976B using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
Jesus
@Lilyankee I need to get my eyes checked. I missed that you did a bolt delete on the strap. Awesome!
@Lilyankee I like it !
Will you be selling SS handle straps, with plugged welded studs?
If so, depending on price I'll take three.
Quote from: ReanimatedRobot on September 01, 2020, 03:10:51 AM
Jesus @Lilyankee I need to get my eyes checked. I missed that you did a bolt delete on the strap. Awesome!
(https://media1.giphy.com/media/Y0V3J57dbIEKzVCkQr/giphy.gif)
Sent from my iPhone using Tapatalk
(https://uploads.tapatalk-cdn.com/20200901/7253cf93b6b74f7db603524ed0d2cfec.jpg)
So the newer plastic handles that come on the later model grills do not fit on this handle strap. Those are curved at the end, so it is necessary to use a single screw or double screw/rivet replacement handle. Zav handles and original old wood handles will fit on this mod. Hardware is 1/4"-20, the same as factory Weber.
I may make a pile of them if there is interest.... lets respond to this post for a week and see how much interest there is. I am willing to make them and ship stateside (sorry my overseas friends, I am not familiar with shipping out of the US) Pricing would be determined by interest.
Sent from my iPhone using Tapatalk
I would definitely be in for at least a half dozen......
I would buy a couple
I would be in for 6 at the moment.
Not sure if the existing shield would fit, but these are pretty awesome.
Those are awesome! I'd be interested. Keep us posted on the price.
@Craig @Lowbrass
I would be interested in a couple depending on price.
Put me down for a couple please.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Looks like excellent work. Interested depending on price.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I think I'd be down depending on price
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I measured at lunch and these would be perfect also for the Weber Fireplace lids.
Ok.
They fit the fireplace lids, I am interested in a pair.
Sent from my SM-G960U using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
My fireplace would also like a pair.
At least 4 or 5 or 6
Sent from my SM-G975U using Tapatalk
My number keeps going up too! Starting to wonder if I will want more than 6 in case I find a fireplace lol
Quote from: JEBIV on September 01, 2020, 03:08:51 PM
At least 4 or 5 or 6
Sent from my SM-G975U using Tapatalk
Sent from my SM-G981U using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
Okay folks, that is enough to make it worth while. The volume helps drive the price down for manufacturing. I'll explore the best method to sell be it Venmo, PayPal, etsy and let you all know in the for sale area of the forum in the upcoming week. Leadtime will be determined once I have the first wave of purchasers intended and get the order made.
Sent from my iPhone using Tapatalk
Quote from: ReanimatedRobot on September 01, 2020, 06:07:41 AM
I would be in for 6 at the moment.
Not sure if the existing shield would fit, but these are pretty awesome.
The shield/taco does not work with this handle. It is intended to delete the new rounded taco handle, or add in place of a torn off handle on an old lid. The hole pattern fits to the new kettle lids which is the same distance as the spot welds on the older kettle lids with welded on handle.
Sent from my iPhone using Tapatalk
Just an awesome mod...I'm in for at least too, tree, probably more.
Sent from my SM-G970U using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
I'd be in for at least one. Maybe three if it fits my Ranch too.
Sent from my iPhone using Weber Kettle Club mobile app (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
No worries. These look great so I am still down for 6 or 7. If I really need a shield I don't think it would be too hard to make one similar to what they had on some older 26ers. It wasn't so taco in shape with the sides bent slightly up. Much better look than the taco.
Quote from: Lilyankee on September 01, 2020, 03:38:43 PM
Quote from: ReanimatedRobot on September 01, 2020, 06:07:41 AM
I would be in for 6 at the moment.
Not sure if the existing shield would fit, but these are pretty awesome.
The shield/taco does not work with this handle. It is intended to delete the new rounded taco handle, or add in place of a torn off handle on an old lid. The hole pattern fits to the new kettle lids which is the same distance as the spot welds on the older kettle lids with welded on handle.
Sent from my iPhone using Tapatalk
Sent from my SM-G981U using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
Any chance to get some cut to fit older MT handles with the thermo between?? Thanks @lilyankee
Sent from my SM-G970U using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
I could do 6 if you want to ship to Canada.
I'd be in for 2.
I'm picking up a 71-75 yellow tomorrow that has the lid handle bracket missing, two very small holes where the weld was. How do I go about ordering one???
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I'm interested in a few depending o price.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I definitely want in...need as many as 6 depending on pricing!
Sent from my iPad using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I'll buy a couple
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I'm in for six!
Sent from my iPhone using Weber Kettle Club mobile app (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Should we start a list in this thread with our name and the quantity that we are interested in to show how large of a run to make?
Sent from my SM-G960U using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
Order your replacement handle strap on the new thread started in this forum!
Order your Lilyankee replacement handle here! http://weberkettleclub.com/forums/index.php?topic=46634
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Quote from: Scott Zee on September 02, 2020, 06:50:44 AM
Any chance to get some cut to fit older MT handles with the thermo between?? Thanks @Lilyankee
Sent from my SM-G970U using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
@Scott Zee I will see if
@Lilyankee can produce these as well.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Damn the taco. Who needs the taco? Crazy people need the taco. Send them your taco.
I am a rare person that like the taco (or potato chip) handle.
Quote from: LightningBoldtz on September 22, 2020, 05:02:36 PM
I am a rare person that like the taco (or potato chip) handle.
Certainly not a potato chip. Maybe a potato crisp like a Pringle?
Sent from my iPhone using Weber Kettle Club mobile app (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I'd buy two. I don't care about price.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I will buy three.
I will take one - just bought a white lid with no hardware.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Quote from: Transit98 on April 25, 2021, 10:50:48 PM
I will take one - just bought a white lid with no hardware.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I have you on the list Transit98
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Hello! I'm now in the market for two of these.
I'm interested in these as well please