They weren't cheap and they haven't been on the grill long but hop they can be brought back to somewhat decent looking.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I'm not a pro at wood refinishing, but given its current state, it shouldn't hurt to give it a light sanding, stain and coat with polyurethane. Shouldn't be too hard. I'd just go easy on the sanding and take your time with medium grit and move to fine grit to get it nice and smooth. Polyurethane products should have directions on the can - usually a light fine grit sanding between coats. Some stains also come combined with poly to save time.
I would probably try one of the Formby's strippers that just removes the topcoat without really removing the stain, bonus is little to no sanding may be needed. Then decide what kind of top coat you want, I'd consider a Tung oil or something similar so when the finish fades a bit a quick buff with some 1000 steel wool and you can apply another coat or two to refresh the look.
If you know who made it you could always try reaching out to them and see what they top coated it with as that could change how you might refinish it as it is now.
Thanks
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Quote from: bamakettles on March 11, 2020, 11:26:36 AM
I'm not a pro at wood refinishing, but given its current state, it shouldn't hurt to give it a light sanding, stain and coat with polyurethane. Shouldn't be too hard. I'd just go easy on the sanding and take your time with medium grit and move to fine grit to get it nice and smooth. Polyurethane products should have directions on the can - usually a light fine grit sanding between coats. Some stains also come combined with poly to save time.
+1
Lacquer is too thin. Multiple polyurethane coats is a good answer that can hold up to weather (cold/snow or intense sun) if you build it up (stain first if you want it tinted). If you want to sand them down and stain (or not), then build up coats and you'll have a product that will last a bit longer. I have handles from the same seller and have brought up the issue to them months ago. Long story short...you're on your own to fix this.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Here what I use saving original handles.... after a light sanding, and then a little 0000 steel wool.
Sent from my SM-G950U using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)
Helmsman is great stuff. I used it on some wood table legs and they're going on 3 years with no issues. It comes in a rattle can too. Protects against moisture and UV.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
I use the same spar varnish, only the aerosol version. Several thin coats with a light polish using 4/0 steel wool between coats.
Sent from my SM-G960U using Tapatalk
Is there a finish on them? Do you have to sand them down like fine antique furniture with a liquid deglosser and then treat them with whatever finished you would like satin usually or if they do not have any finish, use teak oil
Quote from: captjoe06 on March 11, 2020, 11:19:01 AM
They weren't cheap and they haven't been on the grill long but hop they can be brought back to somewhat decent looking.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Did they burn?
Quote from: captjoe06 on March 11, 2020, 11:19:01 AM
They weren't cheap and they haven't been on the grill long but hop they can be brought back to somewhat decent looking.
Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)