Weber Kettle Club Forums

Grill Talk => Weber Mods, Tables and Customs => Topic started by: bluewhisper on February 23, 2018, 05:21:54 AM

Title: DaWeber code M gets a rehab
Post by: bluewhisper on February 23, 2018, 05:21:54 AM
In some recent warm weather, I took some time to overhaul the 22-inch I rescued last year. I found it abandoned among a yard full of junk when the neighbors were moving out. I don't know how long it had been sitting with the lid off, next to a soggy half-bag of charcoal, but there was a circle of dead grass under the lid. I gave the rack a quick cleaning and ran a fire to burn out any Evil Spirits, spiderwebs, bedbugs and Russian hackers. I cooked on it a few times and it was OK but still needing love.

I began with the wooden handles, which looked like they were part of an old barn. I took them off and sanded them with 60, 100, and 320-grit sandpaper. The outer gray layers of wood were crumbly but I was able to get down to solid wood. Then I rubbed them generously with "cutting board oil" so they have a nice luster again. The top handle still has a little bit of darkness on one end, and I'll just consider that to be Character.

I polished the lid with a cloth and Bar Keeper's Friend and rinsed it with water from the rain barrel (pure rain water, Mandrake). Based on a youtube video from a member of this board, I used a safety razor paint scraper to remove a lot of Unspecified Dark Material from the inside of the lid, since I didn't want it falling on my food. The vent was in good working order but it looked better after I scoured it.

The bottom vents were stuck partly open, and after a bit of trying them I found out they were STUCK with crust. At first I tried tapping on the tabs with a hammer but I quickly realized that was just bending the tabs. So I used locking pliers to hold the tabs, and tapped on the pliers. There was a lot of resistance, and i resorted to using spray grease to free them up so they could turn freely. Then I used engine starting spray to purge out the grease.

I pulled out the legs and used a stainless steel scouring pad to polish them and the shelf. The shelf hook had come out of the front leg, but with some bending and persuasion I got it to stay in snugly, but I could still pop it out if I wanted - I want to be able to take the legs off to transport the kettle. I scraped out the inside of the bottom, as I had with the lid.

The charcoal grate's wires were spaced wide enough apart to let briquettes fall through. I tried to replace it with another round grate I had on hand, but it was just barely too small to rest on the tabs. So I simply laid it over the original, at a right angle, problem solved.

Then I used the steel pad to scour the cooking grate. I didn't bother to take it all the way down to the chrome finish; I just made it smooth to the touch. There was no rust.

And that was it. Later I made a small fire of scrap wood in it, just to cook out any of the grease in the bottom vents. Now it's looking new and pretty and good to go.


[attachment deleted by admin]
Title: Re: DaWeber code M gets a rehab
Post by: JEBIV on February 23, 2018, 05:32:44 AM
nice rescue and restore
Title: Re: DaWeber code M gets a rehab
Post by: bluewhisper on February 23, 2018, 05:41:59 AM
Thanks! I left out the pic of the charcoal grate.


[attachment deleted by admin]
Title: Re: DaWeber code M gets a rehab
Post by: Firemunkee on February 23, 2018, 09:29:36 AM
Nice!! Thanks for sharing all the details. I have some handles I've been meaning to restore (only sanded so far) but never thought to use my cutting board oil. I'm going to give that shot.
Title: Re: DaWeber code M gets a rehab
Post by: jcnaz on February 23, 2018, 08:41:55 PM
Very nice work!
Title: Re: DaWeber code M gets a rehab
Post by: Lowbrass on February 24, 2018, 07:46:53 AM
Very nice restore! Loved reading the step by steps!


Sent from my iPad using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Title: Re: DaWeber code M gets a rehab
Post by: Darko on February 24, 2018, 09:24:53 AM
I always love seeing how dirty old kettles look almost like new after a good cleaning. It really is a statement to Weber's quality.
Title: Re: DaWeber code M gets a rehab
Post by: Firemunkee on February 24, 2018, 09:29:48 AM
I have an M and J code kettles and neither of them have the daisy vents on the bowl. Was the one touch system an upgrade on the kettles these age?

Sent from my Nexus 5X using Weber Kettle Club mobile app (http://r.tapatalk.com/byo?rid=91018)

Title: Re: DaWeber code M gets a rehab
Post by: Larry The BBQ Guy on February 24, 2018, 08:49:21 PM
Nice restoration. Thanks for the great images. You can use some cooking spray on the bottom vents now that you have purged the bad stuff. That will help protect the raw metal around the vent screw holes.
Title: Re: DaWeber code M gets a rehab
Post by: Dh Jam1 on February 26, 2018, 08:32:52 PM
Very nice, i will be sanding my handles down now
Title: Re: DaWeber code M gets a rehab
Post by: Grillagin on February 27, 2018, 11:17:38 PM
Great job!  Nice to see it found a loving home, and a new life. 
Title: Re: DaWeber code M gets a rehab
Post by: bluewhisper on February 28, 2018, 10:58:39 PM
OK one more step taken, I got a rubber foot for the front leg so it won't bang on the pavement when I move the kettle. It was sold as a crutch tip at a medical supply store, to fit on a 1-inch shaft and it cost only $1.49. It fit perfectly.

Funny side note: When I went to that store and explained what I wanted, the clerk was also a Weber owner and he knew exactly what I was talking about.

But this still isn't what I want because now the leg grabs at the ground. The problem is, as I'm sure you know, when rolling the kettle it's easy to let the front leg hit the ground. I need to get some kind of furniture glide, like a giant thumbtack, that can slide. That should be easy.
Title: Re: DaWeber code M gets a rehab
Post by: Cellar2ful on March 01, 2018, 06:51:51 AM
Quote from: bluewhisper on February 28, 2018, 10:58:39 PM
OK one more step taken, I got a rubber foot for the front leg so it won't bang on the pavement when I move the kettle. It was sold as a crutch tip at a medical supply store, to fit on a 1-inch shaft and it cost only $1.49. It fit perfectly.

But this still isn't what I want because now the leg grabs at the ground. The problem is, as I'm sure you know, when rolling the kettle it's easy to let the front leg hit the ground. I need to get some kind of furniture glide, like a giant thumbtack, that can slide. That should be easy.

Ace hardware carries the leg caps.  Part# 56920. They slide rather than grab like a crutch end cap.  Crutch tips are designed to grab and are made of rubber. The Ace leg caps are hard plastic.

http://www.acehardware.com/product/index.jsp?productId=1286863


(http://pics.weberkettleclub.com/images/2017/09/02/pACE3-998130enh-z6.jpg)
Title: Re: DaWeber code M gets a rehab
Post by: mhiszem on March 01, 2018, 09:56:13 AM
Nice cleanup


Sent from my iPhone using Weber Kettle Club mobile app (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)
Title: Re: DaWeber code M gets a rehab
Post by: bluewhisper on March 01, 2018, 12:37:05 PM
Thanks for the tips tip.

I'll find some of those but I think I'll keep the rubber tip for another project. I think I'll get some 1-inch steel conduit and cut it to length for a lowrider version for camping trips. But if I do that' I'll start another thread.
Title: Re: DaWeber code M gets a rehab
Post by: bluewhisper on March 02, 2019, 09:18:03 AM
OK, now for an update about that front leg.

As I said,the bare-ended front leg bangs and hops which is bad for the weld. I put a rubber crutch tip on, and that was an improvement, but it still grabs.

So I installed a metal furniture glide, made to screw into a table or chair leg. I set it at an angle to the rubber foot, so as to sit flat on the pavement. It worked! Now the Weber glides around easily with the touch of a finger.

Title: Re: DaWeber code M gets a rehab
Post by: jimz on March 02, 2019, 10:29:19 AM
Nice job!


Sent from my iPhone using Weber Kettle Club (https://siteowners.tapatalk.com/byo/displayAndDownloadByoApp?rid=91018)