In response to this post http://weberkettleclub.com/forums/member-sales-trades/22'-wsm-middle-section-free-to-good-home-n-ca/ I had to share this.
Some folks were wondering what they could do with a 22" WSM center section. Well I had one that was out of round from my Gen 1 2010 WSM that Weber replaced. I had already gotten a Cajun Bandit Conversion kit and was getting down with the Rib-O-Lator and a Weber rotisserie ring when I decided to make the extra center section a dedicated WSM rotisserie setup. Well, no sooner than I did that Chris Perres rolled out the Cajun Bandit Reversible WSM/Kettle ring. So my creation became a spider collector!
I had been cutting off the bowl lips of rustbucket kettles for some of my Drum Smokers to use with a rotis and Weber lid, naming it the "soon to be patented swamprb UDS/Weber kettle lid mod" or the "Flange Mod". So.... I figured, why not make one for the 22" WSM and use a kettle lid on it??
This is one for my BPS drum that is removable and allows me to use the drum lid or a Kettle lid/rotisserie ring.
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/IMG_1004.jpg)
Here is what I did for the 22" WSM center
Cut 1 1/4" off the bowl of a 22" to set in the top of the WSM center to hold the lid.
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_1970.jpg)
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_1971.jpg)
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_1972.jpg)
I wanted this to be removable in case I stumble across a WSM lid so it just sits in the channel
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_1969.jpg)
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_1973.jpg)
So, since the center is somewhat out of round and the "flange" has some gaps between the channel, I fashioned some braces that are pop riveted in place and tightly secures the lip inside the center section and rest on the grate tabs.
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_1974.jpg)
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_1976.jpg)
To make a tight seal, I used some 5/8" fibreglass rope gasket and Permatex High Temp silicone to adhere it to the "flange".
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_1977.jpg)
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_1978.jpg)
Thats my story and I'm sticking to it!
(http://i163.photobucket.com/albums/t310/swamprb/Ugly%20Drum%20Smoker/Weber/IMG_1979.jpg)
Stay Hungry!
Great work swamp!!, I like that its removable
Good work! That lid adapter is very cleverly done.
If someone with some metal skill sold these at a reasonable price, I would be interested.
I have an extra midsection that was warranty replaced for my old 18" WSM that could be used on an 18" kettle.
Also this would make multiple midsections stack-able.