Weber Kettle Club Forums

Grill Talk => Weber Kettle Forum => Topic started by: TheDude on July 25, 2015, 05:31:08 PM

Title: Help with first RRR
Post by: TheDude on July 25, 2015, 05:31:08 PM
How do I get this, at least to the point of a new wood handle fitting?

(http://i1222.photobucket.com/albums/dd487/sickofcichlids/1BFFD0E5-C4C7-44D8-8951-C7DBB21590F5.jpg) (http://s1222.photobucket.com/user/sickofcichlids/media/1BFFD0E5-C4C7-44D8-8951-C7DBB21590F5.jpg.html)
Title: Re: Help with first RRR
Post by: 1911Ron on July 25, 2015, 05:46:58 PM
I have had success with a rubber mallet and tapping gently to get my handle straight, just go slowly and be forewarned it may pop the weld on the one side.
Title: Re: Help with first RRR
Post by: TheDude on July 25, 2015, 05:54:13 PM
Yeah, that weld on the right doesn't look like it will take much. This is a 97'. Old enough to to restore. Young enough to hone my skills. The front leg also falls right out of socket when you lift on the bowl handle. I was given a tip to put a broom handle in the leg, but yet to figure it out. I plan to keep this thread going as I work on her. The vent handle is also bent a bit, but I may not mess with that. It's fully functional. Bottom vents just need some rust cleanup. I think som oil and #0000 will do the trick there.
Title: Re: Help with first RRR
Post by: 1911Ron on July 25, 2015, 06:02:13 PM
With the leg insert the broom handle into the leg and gently spread the opening a little, don't do to much as you want to have it fit still, some have used a strip of aluminum tape around the top of the leg to help provide friction to hold the leg in.
Title: Re: Help with first RRR
Post by: TheDude on July 25, 2015, 06:16:29 PM
That helps a lot.
Title: Re: Help with first RRR
Post by: 1buckie on July 25, 2015, 07:48:22 PM
"I was given a tip to put a broom handle in the leg, but yet to figure it out."

I might not have explained that right.....Ron's got you covered....either a dowel / broom handle that's just the right size, or if smaller, rotate it around a bit to flare out the circumference of the top of leg to fit tight.....
Title: Re: Help with first RRR
Post by: Craig on July 25, 2015, 07:51:50 PM
These handles are often secured stronger than they appear. I have had luck with taking the head of the rubber mallet and tapping the underside of the lid at the weld points to get the "pushed inward" part of the handle un dented. Then some light taps or my bare hand getting the handle strap straightened. Of course not to aggressive in pounding, just a slight bit of firm force. That should straighten out nicely. As for the bottom, is this a daisy wheel kettle or a One Touch? I'll have to try the aluminum tape method next time I have one with loose leg/socket friction.
Title: Re: Help with first RRR
Post by: TheDude on July 26, 2015, 06:38:46 AM
Quote from: Craig on July 25, 2015, 07:51:50 PM
These handles are often secured stronger than they appear. I have had luck with taking the head of the rubber mallet and tapping the underside of the lid at the weld points to get the "pushed inward" part of the handle un dented. Then some light taps or my bare hand getting the handle strap straightened. Of course not to aggressive in pounding, just a slight bit of firm force. That should straighten out nicely. As for the bottom, is this a daisy wheel kettle or a One Touch? I'll have to try the aluminum tape method next time I have one with loose leg/socket friction.

Daisy wheel.
Title: Re: Help with first RRR
Post by: TheDude on July 26, 2015, 12:07:39 PM
Project nixed for me. Gave it to a friend. I will try to get him to join here. I'm in the preformer club now.