Weber Kettle Club Forums

Grill Talk => Weber Kettle Forum => Topic started by: cbpeck on April 15, 2014, 10:01:57 PM

Title: Questions about those old 5 lb propane tanks on the SS Performers
Post by: cbpeck on April 15, 2014, 10:01:57 PM
Hi guys,

I have plans to look at a SS Performer this weekend, but I have a few questions about those old 5 lb propane tanks. The grill in question does have one, and it appears to be properly suspended in the cart, but I know they have expiration dates, and that some stations will refuse to refill expired tanks. So here is my first question:

1) Where is the expiration date likely to be recorded on the tank? Is it a typical date like 03-10, indicating March 2010, or is it a code of some sort?

I've also read that the fittings are either proprietary, obsolete or a little of both. That leads to my next question:

2) If I ended up needing a new tank could the original fitting (assuming good condition) be removed and reinstalled into the new tank? Is a new 5 lb tank likely to mount in the cart the same way?

I know many of you guys have a ton of experience with these old Performers, but this would be my first, so I really appreciate any and all advice you have to share. Also, I plan to check out the ash sweep, mounting bracket for the ash ring, propane tank, check for rust on the frame & axle, but I think that's about where my knowledge runs out. Please let me know if there's anything else I should check out prior to buying. Thanks in advance!

P.S. Here's a photo of the grill in question:

(http://i1171.photobucket.com/albums/r546/cbpeck/Mobile%20Uploads/00b0b_fnjxnoTYbMi_600x450.jpg) (http://s1171.photobucket.com/user/cbpeck/media/Mobile%20Uploads/00b0b_fnjxnoTYbMi_600x450.jpg.html)
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: DirectDrive on April 15, 2014, 11:30:55 PM
Quote from: cbpeck on April 15, 2014, 10:01:57 PM
Hi guys,

I have plans to look at a SS Performer this weekend, but I have a few questions about those old 5 lb propane tanks. The grill in question does have one, and it appears to be properly suspended in the cart, but I know they have expiration dates, and that some stations will refuse to refill expired tanks. So here is my first question:

1) Where is the expiration date likely to be recorded on the tank? Is it a typical date like 03-10, indicating March 2010, or is it a code of some sort?
Just the month and the year.
I have a 1 gal (5#) tank that has a mfr date of 9-91 and a re-certify date of 5-03.
It also says that tank must be re-certified within 12 years of mfr date.
These marks are going to be on the valve shield (curved piece of sheet metal around valve).

QuoteI've also read that the fittings are either proprietary, obsolete or a little of both. That leads to my next question:
For lack of a better term, there's "old style" which is obsolete and illegal for a vendor to refill and there's OPD (Overfill Prevention Device).
OPD has coarse external threads on the valve...very easy to identify.

Quote2) If I ended up needing a new tank could the original fitting (assuming good condition) be removed and reinstalled into the new tank? Is a new 5 lb tank likely to mount in the cart the same way?
No, most of the SS Performers were from the era of the "old style" valve and have either been re-fitted with an OPD valve or the whole tank was replaced.
That size tank is very expensive...I re-valved/re-certified mine because of that.

QuoteI know many of you guys have a ton of experience with these old Performers, but this would be my first, so I really appreciate any and all advice you have to share. Also, I plan to check out the ash sweep, mounting bracket for the ash ring, propane tank, check for rust on the frame & axle, but I think that's about where my knowledge runs out. Please let me know if there's anything else I should check out prior to buying. Thanks in advance!

P.S. Here's a photo of the grill in question:

(http://i1171.photobucket.com/albums/r546/cbpeck/Mobile%20Uploads/00b0b_fnjxnoTYbMi_600x450.jpg) (http://s1171.photobucket.com/user/cbpeck/media/Mobile%20Uploads/00b0b_fnjxnoTYbMi_600x450.jpg.html)

The condition of the ash sweep that mounting bracket are important but can be fixed/upgraded.
And it's nice if the gas assist works.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: OGlenn on April 16, 2014, 01:43:20 AM
CBPeck, the fitting on the tank is likely a quick-release fitting. Basically, instead of a screw-on/off propane hose attachment, it will have a nipple end piece that goes into a collar on the tank which you must pull backwards in order to insert the nipple.  Manchester produces new tanks with that quick-relase fitting, but they are $55 to $60. Personally, I refilled my empty tank from my 20lb tank, but re-certification is also an option if it is over 12 years old.

The OPD is inside the tank. You'll see a label of the on/off valve will be triangular in shape. Star-shaped-handled OPD tanks I think are rare, but they exist (I have one which is properly labelled OPD). Most star handles are not OPD.

In any event, if there is gas in the tank, know that you won't need to worry immediately as the 5 lbs lasts a very long time. What you may wish to do is test the ignition. If it doesn't light, don't fret as it is VERY likely you'll only need to fully clean out the burner tube, but you may have a chance to negotiate the price down by mumbling that having to buy a new igniter and burner costs $50...


Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: Winz on April 16, 2014, 02:30:46 AM
That is a good looking SS Performer! 
I had to have the valve on my first SS performer upgraded to OPD, and have the tank re-certified.  They simply removed the old valve and replaced it with an OPD device, refilled the device, and put a new certification sticker on it.  I believe it was ~ $35.  If the handle looks like the one on the left below, or if it is round, you will likely be looking at replacing the valve.  The one on the right is OPD.

(https://dl.dropbox.com/s/3n1z55abi5nny5f/OPD.jpeg)

Since you have some time, call a couple of propane dealers and ask them about the cost of upgrading a tank to OPD to get a budgetary figure in mind in case you need it.

I see that the kettle you are looking at has the old style ash sweep.  Finding replacements can be difficult so be sure it is relatively rust free and in good working condition or you are looking at replacing the ash sweep at a minimum, or upgrading the whole system (new sweep, bracket, and ash pan).  Gummi wrote a great guide to upgrading ash sweep assemblies:  http://weberkettleclub.com/blog/2014/03/03/converting-a-weber-ots-to-otg/ (http://weberkettleclub.com/blog/2014/03/03/converting-a-weber-ots-to-otg/)

The SS performers are built like a tank and are made to last - my favorite Weber model!  Hope this one works out for you.

Winz
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: MINIgrillin on April 16, 2014, 03:31:33 AM
The starter element can be cleaned if it doesn't work on the first shot. Probably has crud build up on the electrode tip. It's a 5min fix.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: addicted-to-smoke on April 16, 2014, 04:19:13 AM
cbpeck, that's got a "flat top" plastic lid handle, like my '92 has. The hose on the '92 predates quick-disconnect; yours may as well: I had to use a wrench to unscrew my tank's hose. Doesn't matter because you aren't going to use your old tank unless it's been switched over to OPD, as noted above.

If everything is good and you just need to adapt to the OPD tank, screw this into your regulator: http://www.lowes.com/pd_361433-743-GFA-100_0__?Ntt=acme+nut&UserSearch=acme+nut&productId=50142158&rpp=32 Here's an ACME (i.e. QCC1) adapter + regulator: http://www.lowes.com/pd_361431-743-GRA-100_0__?productId=50142154&Ntt=benzomatic+propane+regulator&pl=1&currentURL=%3FNtt%3Dbenzomatic%2Bpropane%2Bregulator&facetInfo=

You can also get a longer pigtail and use a 20lb tank but you'll have to give up the charcoal bin and be careful when moving the grill around.

If you use a chimney with the gas, or a chimney with paraffin cubes with the gas, you'll use a lot less gas and so, might be a candidate for the little 1lb "disposable" tanks used on the plastic-tabletop Performers. Weber sells a complete, new hose/regulator assembly for less than $35 I think. Or you might try just the fitting and reuse your regulator?: http://www.amazon.com/Mr-Heater-F273754-Throwaway-Cylinder/dp/B000BQM8IU/ref=pd_sim_hg_1?ie=UTF8&refRID=1CCBGGVNRNGD5SHX6FM2 Of course, with anything that's not a alb tank you're looking at a modification to get it supported.

NON-TANK parts:
Let's assume the burner tube is good and just needs to be blown out/hosed out. Let's assume you'll also clean out the element, as MINIgrillin suggests (a tiny wire in the pinhole should do it, the element disconnects from the burner tube with a C-clip.) Let's further assume the ignitor/switch/wiring is OK.

The rest is hose/regulator/tank fitting, with reused, purchased piecemeal or as an assembly. Weber has a complete assembly (part #62642) for modern OPD-valve 5lb-20lb tanks but call Weber, as ereplacements' price is crazy high.


Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: cbpeck on April 16, 2014, 05:22:51 AM
Thanks for the info guys. It sounds like if necessary - and it probably will be - I can have the tank recertified, which will include installing an OPD valve, while probably maintaining the existing connections, for the most part. I may need to make a minor change or two, bit it is unlikely everything will need replacing. But if it comes to that, I can get a new gashose assembly from weber that will connect to tthe existing burner tube & a current, standard production propane valve (which would be installed in the original tank or a replacement).

Whatever tank I end up with, I would like it mounted properly under the cart. I would prefer to not have a tank sitting on the lower shelf or to discard the charcoal caddy.

I have an 11 lb pancake tank for  car camping, so I know these little guys can be pricey.

Thanks again for the tips!
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: addicted-to-smoke on April 16, 2014, 07:49:56 AM
You and I have the same goals regarding the SS. Since you already have another tank that's otherwise compatible, you can use it to test, right?

In other words if your regulator works you'll just need that $5 QCC1 adapter for your re-certified/new valve'd 5lb tank. Even if your igniter is shot you'd still be able to hear the hiss of gas coming out of the burner tube, assuming it and the element are cleared/clean.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: cbpeck on April 16, 2014, 10:21:47 AM
Quote from: addicted-to-smoke on April 16, 2014, 07:49:56 AM
You and I have the same goals regarding the SS. Since you already have another tank that's otherwise compatible, you can use it to test, right?

In other words if your regulator works you'll just need that $5 QCC1 adapter for your re-certified/new valve'd 5lb tank. Even if your igniter is shot you'd still be able to hear the hiss of gas coming out of the burner tube, assuming it and the element are cleared/clean.

Thanks. The seller states the tank is full & the ignitor works, but we'll see when I get there. One thing I do know is that I will likely only have one Performer, so I would like it to be a nice one. It looks good in the photos and sounds good in the description, so hopefully it looks just as good in person.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: Bman on April 16, 2014, 04:58:19 PM
Quote from: DirectDrive on April 15, 2014, 11:30:55 PM

OPD has coarse external threads on the valve...very easy to identify.

All very good information in this thread, but I wanted to add to the above.  Not all OPD tanks have the external threads.  I have a few SS Performers from 98' and all have the quick connect fitting, (no external threads) and the OPD triangular valve.

For what it's worth, it only cost me $3.15 plus tax last summer to have a completely empty 5# tank filled at my local lumber yard.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: DirectDrive on April 16, 2014, 05:58:40 PM
Quote from: Bman on April 16, 2014, 04:58:19 PM


All very good information in this thread, but I wanted to add to the above.  Not all OPD tanks have the external threads.  I have a few SS Performers from 98' and all have the quick connect fitting, (no external threads) and the OPD triangular valve.



It is my understanding that the station refill apparatus engages these external threads.
Have you had these tanks refilled lately ?
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: mike.stavlund on April 16, 2014, 06:07:42 PM
All good info, and I'll second what Bman said:  I have a couple of OPD 5lb tanks, and I haven't had any trouble getting my tanks filled, regardless of age.  The guys filling them at U-Haul simply never look at the dates.  I'd be worried about them potentially leaking, but all of them are kept outside. 

One thing you might watch out for, though:  some of the tank filling dudes are pretty green, so you should keep an eye out that they don't put more than about a gallon of gas into the tank.  I've had one overfilled once, and it was impossible to turn off the flame. 

And I hear you, cbpeck, about wanting a good SS if you're going to get one, but remember that you will likely see another come around again.  Kettle karma has a way of working like that.  But on the whole, try not to worry too much about igniters and the like, which are easy to fix/replace.  Make sure you've got a good solid frame and no rust.  I've seen a few SSs that suffered some serious degregdation on the lower end with rusty frame tubes and star nuts, and fixing them didn't bring about the greatest results.  You also might want to peek underneath both stainless steel table sections, as the crossmembers on the frames can get pretty rusty under there.   
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: mike.stavlund on April 16, 2014, 06:11:17 PM
Quote from: DirectDrive on April 16, 2014, 05:58:40 PM
Quote from: Bman on April 16, 2014, 04:58:19 PM


All very good information in this thread, but I wanted to add to the above.  Not all OPD tanks have the external threads.  I have a few SS Performers from 98' and all have the quick connect fitting, (no external threads) and the OPD triangular valve.



It is my understanding that the station refill apparatus engages these external threads.
Have you had these tanks refilled lately ?

My refill guys at U-Haul have a whole selection of valve fittings, including one for a quick-connect tank. 

The refill guys at my BJ's (a warehouse place similar to Sam's or Costco) don't. 
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: cbpeck on April 16, 2014, 06:19:47 PM
Thanks again guys, including Mike. The grill is located roughly 150 miles away, and I can't get there until Friday. The seller just emailed me saying "looks like somebody is going to come pick it up Thursday night." I'm a little annoyed, frankly. I knew he wasnt going to hold it, but even so. I do plan to add a ss performer one day, so i guess it doesnt have to be this one. I know more will come around. In the mean time, I'm going to pretend this one is a rustbucket that I didn't want, anyway.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: utahusker on April 16, 2014, 06:31:33 PM
Is there a quick connect adaptor that changes them to external threads .


Sent from my iPad using my awesome typing skills.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: javahog2002 on April 16, 2014, 09:50:24 PM
Mine have never been turned away from 3.different propane shops.  Ace hardware was one of them. My tank does have the opd.  If the handle is star shaped it does not have an opd. The triangle shaped handled tanks do have an opd.  I have seen a large tank with an adaptor to run a propane heater which uses the same quick release fitting.

Sent from my Atari 2600 using Tapatalk.

Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: javahog2002 on April 16, 2014, 09:54:15 PM
If the bluey is gone, u will find one. I had 3.for a while. One was free and I bought the other two on the same day.

Sent from my Atari 2600 using Tapatalk.

Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: addicted-to-smoke on April 17, 2014, 03:41:04 AM
Quote from: mike.stavlund on April 16, 2014, 06:07:42 PM...

One thing you might watch out for, though:  some of the tank filling dudes are pretty green, so you should keep an eye out that they don't put more than about a gallon of gas into the tank.  I've had one overfilled once, and it was impossible to turn off the flame.  ...

This would seem like a good reason to only use a tank with an OPD (i.e. Overfill Protection Device) valve.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: mike.stavlund on April 17, 2014, 08:44:46 PM
Quote from: addicted-to-smoke on April 17, 2014, 03:41:04 AM
Quote from: mike.stavlund on April 16, 2014, 06:07:42 PM...

One thing you might watch out for, though:  some of the tank filling dudes are pretty green, so you should keep an eye out that they don't put more than about a gallon of gas into the tank.  I've had one overfilled once, and it was impossible to turn off the flame.  ...

This would seem like a good reason to only use a tank with an OPD (i.e. Overfill Protection Device) valve.

Absolutely correct!  Though in my case I simply disconnected the tank between uses until the pressure went down to a normal level. Still, not the safest situation.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: utahusker on April 18, 2014, 06:53:39 AM
I have a 5 lb OPD tank that has a quick connect.  Is there an adapter I can buy to make it external threaded for filling?  The reason is, no one here has an adapter so they can't fill a quick connect tank.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: DirectDrive on April 18, 2014, 08:07:49 AM
Quote from: utahusker on April 18, 2014, 06:53:39 AM
I have a 5 lb OPD tank that has a quick connect.  Is there an adapter I can buy to make it external threaded for filling?  The reason is, no one here has an adapter so they can't fill a quick connect tank.
Your local propane supply store may have something.

Or if your quick connect fitting looks like this and you have the tool shown in the pic you could remove the QC for refilling.
That would sort of cancel out the usefulness of the QC though. Which IMO, isn't really that useful for this application anyway.
(http://ace.imageg.net/graphics/product_images/p1226569dt.jpg)


Or convert to a hose with a hand wheel at the tank end and eliminate the quick connect.
(http://img2.wfrcdn.com/lf/46/hash/2195/6368807/1/Mr.-Heater-20-Propane-Hose-Assembly.jpg)

Whichever way you decide to go, you will find a better assortment of hardware at your local propane supplier's store.
And of course, much more expertise as well.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: DirectDrive on April 18, 2014, 06:02:50 PM
Update :

Checked with one of my local propane guys and he still has a stinger that engages the internal threads. He could still fill an old POL valved tank but it would violate Federal law.
He has an adapter for a quick connect and also an adapter for the OPD external threads.
He said that sometimes he will see an OPD valve without the internal threads.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: gunner on April 19, 2014, 12:30:13 PM
Hey Folks,

Hoping you can help me! I am having trouble getting the ignition to light the burner on my SS cart. When I turn on the gas I can get the gas lit by using a lighter so I know gas is getting to the tube. I even swapped out an ignition switch from a working newer performer to see if the old ignition is shot but I couldn't get that one to work either. What would you guys do next to trouble shoot?

This is my connection, it is a quick release and the propane tank is OPD certified. It came with the grill so I don't know if I will have trouble getting it refilled?
(http://im1.shutterfly.com/media/47a4da38b3127ccef5b21fa9625600000030O10AauGbFk0ZuGQPbz4U/cC/f%3D0/ls%3D00208342138520140419201904661.JPG/ps%3D50/r%3D1/rx%3D720/ry%3D480/)

(http://im1.shutterfly.com/media/47a4da38b3127ccef5b35f50c3f300000030O10AauGbFk0ZuGQPbz4U/cC/f%3D0/ls%3D00208342138520140419201908787.JPG/ps%3D50/r%3D1/rx%3D720/ry%3D480/)

(http://im1.shutterfly.com/media/47a4da38b3127ccef5b32ab083b100000030O10AauGbFk0ZuGQPbz4U/cC/f%3D0/ls%3D00208342138520140419201912784.JPG/ps%3D50/r%3D1/rx%3D720/ry%3D480/)
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: pbe gummi bear on April 19, 2014, 01:36:01 PM
Quote from: gunner on April 19, 2014, 12:30:13 PM
Hey Folks,

Hoping you can help me! I am having trouble getting the ignition to light the burner on my SS cart. When I turn on the gas I can get the gas lit by using a lighter so I know gas is getting to the tube. I even swapped out an ignition switch from a working newer performer to see if the old ignition is shot but I couldn't get that one to work either. What would you guys do next to trouble shoot?

This is my connection, it is a quick release and the propane tank is OPD certified. It came with the grill so I don't know if I will have trouble getting it refilled?
(http://im1.shutterfly.com/media/47a4da38b3127ccef5b21fa9625600000030O10AauGbFk0ZuGQPbz4U/cC/f%3D0/ls%3D00208342138520140419201904661.JPG/ps%3D50/r%3D1/rx%3D720/ry%3D480/)

(http://im1.shutterfly.com/media/47a4da38b3127ccef5b35f50c3f300000030O10AauGbFk0ZuGQPbz4U/cC/f%3D0/ls%3D00208342138520140419201908787.JPG/ps%3D50/r%3D1/rx%3D720/ry%3D480/)

(http://im1.shutterfly.com/media/47a4da38b3127ccef5b32ab083b100000030O10AauGbFk0ZuGQPbz4U/cC/f%3D0/ls%3D00208342138520140419201912784.JPG/ps%3D50/r%3D1/rx%3D720/ry%3D480/)

It sounds like you have a bad ground. Clean up the connection at the burner tube/piezo/screw. Also check the tip of the piezo that it's not all gunked up. If it it, clean it off with a brush and some sandpaper.

Step 5 and 6 below should help.

Quote from: pbe gummi bear on May 13, 2013, 10:46:45 AM
Touch N' Go Gas assist repair

Sorry no pics here right now, but here is what I did to fix my igniter.

First I made sure that the there was still propane. I could feel the liquid in the tank, hear it when opened, and use a match to light the burner tube. But my igniter didn't work.

Here is my igniter fixing flowchart:

0. Make sure the igniter button isnt wet.

1. Is there liquid propane still in tank? Shake it lightly and feel for it.

2. Connect all the lines.

3. Are you getting good propane flow through the tube, and regulator? Open the valve on the tank. you should be able to hear the tank hissing when you open it and smell the propane. DO NOT STICK YOUR HEAD IN THE BOWL. If you don't hear the hissing or smell, close the valve. There is another brass valve parallel to the regulator hose. Make sure that little valve handle is open (pointing parallel to or along the hose). If you don't here hissing still your regulator is probably shot.

4. Try to ignite the flame with the igniter push button or a match. If the igniter button works, great! But it probably won't. If the match works you can skip the tube cleaning step 5,  but it is still useful.

5. Clean the burner tube. To begin fixing the gas assist pop off the clip at the end of the igniter tube. Removing this tube by taking off the igniter ground wire / element and loosening the tube clamp with a slotted screwdriver or wrench will make this a hell of alot easier. You dont need to remove the clamp. Just loosen it and pull the tube into the bowl. You can't pull the tube out without completely taking off the clamp because of the flat end that is wider. Look inside the tube. Chances are there will be ashcrud and cobwebs in it. Clean this all out with water. You can also use sandpaper on the tube to make it nice and shinier again.

6. Test the igniter. remove the igniter button assembly if you haven't already. Hold the igniter wires in one hand and push the buttton with the other. IT SHOULD LIGHTLY SHOCK YOU like static on a doorknob so if you easily yell expletives make sure there are no kids around. If it didn't shock you, your piezo is dead so buy a new igniter. If it shocked you, we can fix it! Take some sand paper and lightly sand the igniter tip until it's clean bare metal. It's pretty stout but be careful not to break it. Also make sure that the ground wire and bolt is not escessively rusty or you may not get a good connection. Mine was moderately rusty but it still worked.

7. Reassemble and retest. Everything should work now. If not, sell your performer and buy a big green egg.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: gunner on April 19, 2014, 02:19:37 PM
Thanks Gummi I will try that! Do you think I will have a problem getting that propane tank refilled?
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: pbe gummi bear on April 19, 2014, 03:00:38 PM
Well you have an opd so that's a good start. A lot of local ace's in Chicagoland have propane fillip stations. Give them a call and ask if they can refill a quick connect tank for an rv. Uhaul does the same service. You can try to get an expired tank at your own risk or get it recertified.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: Bman on April 19, 2014, 05:09:00 PM
Quote from: gunner on April 19, 2014, 02:19:37 PM
Thanks Gummi I will try that! Do you think I will have a problem getting that propane tank refilled?

My "surefire" way of knowing if I have spark or not, is to take the burner tube off the grill, look down the tube, and click the igniter button a dozen times and look for spark.  It should be a nice strong spark.  Unless it's extremely damp outside, it should fire up ok as long as you have spark.

Is it just me, or does the regulator look upside down?

Your tank is the OPD tank and the yellow sticker says so.  As long as your refilling station still has the quick-connect fitting, you should be golden.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: pbe gummi bear on April 19, 2014, 05:11:34 PM
Quote from: Bman on April 19, 2014, 05:09:00 PM
Quote from: gunner on April 19, 2014, 02:19:37 PM
Thanks Gummi I will try that! Do you think I will have a problem getting that propane tank refilled?

My "surefire" way of knowing if I have spark or not, is to take the burner tube off the grill, look down the tube, and click the igniter button a dozen times and look for spark.  It should be a nice strong spark.  Unless it's extremely damp outside, it should fire up ok as long as you have spark.

Is it just me, or does the regulator look upside down?

Your tank is the OPD tank and the yellow sticker says so.  As long as your refilling station still has the quick-connect fitting, you should be golden.

Ooh that's a great tip. I'll make sure to update the step by step and credit you Bman!
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: OGlenn on April 19, 2014, 09:56:13 PM
I can attest that BMan's method of checking the spark works having used it myself - I assumed that was the common sense way everyone used to check. I actually do it while it is attached to the bowl as the shade under the table helps you see the spark even better. If it isn't lighting cleaning out the tube should be an early step in diagnosing.

FWIW, five-point wheels doesn't automatically mean a tank doesn't have OPD, although it usually does. This OPD five-point handwheel tank was on a performer I picked up a few months ago:

(http://i1330.photobucket.com/albums/w579/O_Glenn/P1080909_zps22adf80e.jpg)
(http://i1330.photobucket.com/albums/w579/O_Glenn/P1080910_zpsd39f7bf5.jpg)
(http://i1330.photobucket.com/albums/w579/O_Glenn/P1080911_zps414473f6.jpg)
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: gunner on April 20, 2014, 04:05:49 AM
Quote from: Bman on April 19, 2014, 05:09:00 PM
Quote from: gunner on April 19, 2014, 02:19:37 PM
Thanks Gummi I will try that! Do you think I will have a problem getting that propane tank refilled?

My "surefire" way of knowing if I have spark or not, is to take the burner tube off the grill, look down the tube, and click the igniter button a dozen times and look for spark.  It should be a nice strong spark.  Unless it's extremely damp outside, it should fire up ok as long as you have spark.

Is it just me, or does the regulator look upside down?

Your tank is the OPD tank and the yellow sticker says so.  As long as your refilling station still has the quick-connect fitting, you should be golden.

Haha yeah the regulator is upside down...I just connected it real quick while messing around with it to try and get it to light. Good tip on the burner tube..thanks Bman!
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: drtmcd on April 20, 2014, 04:29:54 AM
Just completed a rebuild of my 1998 Performer. Had a split gas hose which needed replacement. Threw the split one out thinking it would be easy to replace (gas orifice included). Called Weber Customer Service and ordered a replacement hose for my 98 Performer. Received a hose with regulator which fits the new throw away propane tanks. Called Weber and was told I could return the part but that I needed to "convert" my Performer to the new throw away tanks and that Quick Discconnects  could / should not be used. Was told the regulator could not be removed (WRONG) from the new hose. Was told that no one would refill my 5 lb Weber propane tank. WRONG - Ace H is happy to do so.

Obtained the necessary 2 fittings from MSC Industrial Supply Co. which allowed me to connect from the new hose (after removing regualator) and connect from 1/8" NPFT to #6 SAE MALE FLARE of the original Marshall 210.


https://www.mscdirect.com/product/62251038?rItem=62251038

https://www.mscdirect.com/product/83294785?Arg=nv

26.90 including shipping and handling and my gas starter is now working well.
I have written Weber about the solution above and they want no part of it.

From Weber CS:
"Also, the quick disconnect tanks are no longer being filled, and would require a new style hose/regulator assembly for your grill.  Weber sells the necessary replacements for your grill, to use with the newer QCC1 tanks. Replacing the hose/regulator assembly by modifying is not safe, and needs to be replaced with the parts made specifically for the grill."

I have no idea how many federal, state, and local laws I have broken or continue to violate as I get my charcoal burning without problems.

Wish Weber would have paid more attention to using rust resistance parts.  Had to replace the Kettle  ($90.29) and Ash Catcher ($22.90) in order to replace the frozen One Touch cleaning/ air reg.




Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: OoPEZoO on April 20, 2014, 06:15:59 AM
Quote from: drtmcd on April 20, 2014, 04:29:54 AM
  Had to replace the Kettle  ($90.29) and Ash Catcher ($22.90) in order to replace the frozen One Touch cleaning/ air reg.

Why was that?  Couldn't you just cut the old parts off with a cutting wheel and replace them with new hardware without scrapping the bowl?  I ask because I just went through this with SS performer I picked up yesterday. The screws for the tube bracket were rusted beyond use or repair.  I flipped the bowl upside down over a trash can and spent about 30sec on each screw head with my grinder. Uncle the screw head is ground down, you can pull the screw shaft and nut out through the bowl. All I need to do now is clean up the tube bracket, paint it with high temp paint, and replace it using stainless steel hardware. That should keep the problem from returning.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: DirectDrive on April 20, 2014, 07:12:03 AM
Quote from: drtmcd on April 20, 2014, 04:29:54 AM
Just completed a rebuild of my 1998 Performer. Had a split gas hose which needed replacement. Threw the split one out thinking it would be easy to replace (gas orifice included). Called Weber Customer Service and ordered a replacement hose for my 98 Performer. Received a hose with regulator which fits the new throw away propane tanks. Called Weber and was told I could return the part but that I needed to "convert" my Performer to the new throw away tanks and that Quick Discconnects  could / should not be used. Was told the regulator could not be removed (WRONG) from the new hose. Was told that no one would refill my 5 lb Weber propane tank. WRONG - Ace H is happy to do so.

Obtained the necessary 2 fittings from MSC Industrial Supply Co. which allowed me to connect from the new hose (after removing regualator) and connect from 1/8" NPFT to #6 SAE MALE FLARE of the original Marshall 210.


https://www.mscdirect.com/product/62251038?rItem=62251038

https://www.mscdirect.com/product/83294785?Arg=nv

26.90 including shipping and handling and my gas starter is now working well.
I have written Weber about the solution above and they want no part of it.

From Weber CS:
"Also, the quick disconnect tanks are no longer being filled, and would require a new style hose/regulator assembly for your grill.  Weber sells the necessary replacements for your grill, to use with the newer QCC1 tanks. Replacing the hose/regulator assembly by modifying is not safe, and needs to be replaced with the parts made specifically for the grill."

I have no idea how many federal, state, and local laws I have broken or continue to violate as I get my charcoal burning without problems.

Wish Weber would have paid more attention to using rust resistance parts.  Had to replace the Kettle  ($90.29) and Ash Catcher ($22.90) in order to replace the frozen One Touch cleaning/ air reg.
Welcome to the forum !
Great first post.

Weber CS has to "tow the party line" when it comes to parts replacement/advice for the older SS Performer gas system.
They would be slammed with a fine (or worse) if they got caught helping someone keep a non-OPD system in service.
OPD valves have been required since Jan 1, 2003.

I think if I was updating an old Performer to OPD I would see about moving the regulator "down stream".
I am conditioned to having a handwheel hose connection at the tank and no regulator in the way.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: addicted-to-smoke on April 20, 2014, 09:17:38 AM
2-things.

A working setup will (or can) still light the burner in 100% humidity (such as during a light or misting rain. I did just that yesterday.

The other thing is, the benefit of a clean gas orifice can't be overstated. Partially clogged, you'll still get flame but it'll be weak. Full flow produces a much more noticeable flame from the tube.
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: drtmcd on April 20, 2014, 10:12:39 AM
The bar that holds the Ash Catcher was also completely rusted out. The new Ash Catcher Assembly now attaches to the legs and not the bar. That old "bar" is no longer available as per Weber and I could have "saved"  the 98 Kettle by grinding or drilling out the old cotter key part but would not be able to attach my old or a new Ash Catcher Ring.  Thus a new Kettle and Ash Catcher.

I did drill out the 2 rusted bolts which attached the burner unit to the grill to avoid buying a new burner unit.

As i said in my email to Weber:

"I decided to replace the vent control which had "frozen" several years ago so I could control the heat better to do some low and slow cooking.

I bought a 7409 One Touch Kit from GrillStuff for $24.94. I removed the kettle to replace and then found the nut assembly / cotter key at base of kettle to be completely rusted out  as was the bar which connected to the Ash Catcher Ring Assembly.

I called Weber customer service and was told I needed a new Weber Kettle for $90.29 I observed that there was no way to attach the Ash Catcher and bought a new unit (63093) for  $22.90. By this time I was wondering whether I should have just bought a new Weber 22.5 Kettle pit for $149 here in Atlanta, thrown the legs out  and for the "extra" $10.87 difference had a NEW lid/ thermometer/lid catcher/ charcoal baskets/ charcoal grill and 22.5 inch grill."





Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: pbe gummi bear on April 20, 2014, 10:26:03 AM
Quote from: drtmcd on April 20, 2014, 10:12:39 AM
The bar that holds the Ash Catcher was also completely rusted out. The new Ash Catcher Assembly now attaches to the legs and not the bar. That old "bar" is no longer available as per Weber and I could have "saved"  the 98 Kettle by grinding or drilling out the old cotter key part but would not be able to attach my old or a new Ash Catcher Ring.  Thus a new Kettle and Ash Catcher.

I did drill out the 2 rusted bolts which attached the burner unit to the grill to avoid buying a new burner unit.

As i said in my email to Weber:

"I decided to replace the vent control which had "frozen" several years ago so I could control the heat better to do some low and slow cooking.

I bought a 7409 One Touch Kit from GrillStuff for $24.94. I removed the kettle to replace and then found the nut assembly / cotter key at base of kettle to be completely rusted out  as was the bar which connected to the Ash Catcher Ring Assembly.

I called Weber customer service and was told I needed a new Weber Kettle for $90.29 I observed that there was no way to attach the Ash Catcher and bought a new unit (63093) for  $22.90. By this time I was wondering whether I should have just bought a new Weber 22.5 Kettle pit for $149 here in Atlanta, thrown the legs out  and for the "extra" $10.87 difference had a NEW lid/ thermometer/lid catcher/ charcoal baskets/ charcoal grill and 22.5 inch grill."

Sorry you went through all that trouble and cost. Replacement ashbars are available here:
weberkettleclub.com/forums/weber-kettles-accessories/okay-who-is-really-interested-one-one-of-these/
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: Heyjude on April 20, 2014, 10:58:56 AM
Lets clear up a couple things.
You can still use a "Quick Disconeect" on Weber grills. But, the tank needs to be OPD and within the age limits of the law.  We all know that their are some propane dealers who will fill an old tank, but that its probably OPD and not the old Star design.

As for the burner tubes, those are still available. The old reguator and hose assmbly has been updated by weber to use the now standard screw on connector. But its expensive!
If you have your old hose and regulator, don't throw it out!   You can upadte the fittings to the new screw on connector.
Assumong you have a newer tank or are planning on getting one.
If yolu get the newer regulator and valve that Weber put ont he newer Performers, you would have to find a way to mount it to your cart.

There are plent of discussions on the older SS Perfomrers. Do your research and decide what is best for you and then post your tips, ideas and or mods.

Hey drtmcd , did you sy the regulator and hose can be seperated from the newer regulator?
I posted a pic below.. (Second pic)
AJ  8)

(http://www.ereplacementparts.com/images/part_p_1477479_2534160992_med.gif)

(http://www.ereplacementparts.com/images/part_p_1477523_2290167233_med.gif)








Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: Bman on April 20, 2014, 11:11:36 AM
Quote from: drtmcd on April 20, 2014, 10:12:39 AM
By this time I was wondering whether I should have just bought a new Weber 22.5 Kettle pit for $149 here in Atlanta, thrown the legs out  and for the "extra" $10.87 difference had a NEW lid/ thermometer/lid catcher/ charcoal baskets/ charcoal grill and 22.5 inch grill."

If you mean purchasing a new One Touch Gold for 150 bucks, the bowl wouldn't have mounted into the Performer frame as the OTG doesn't have the mounting flanges.

I don't think we're trying to be smart asses and "talk down" to you, but rather trying to assist and offer advice.
I hope that's how you're taking this info.  :D



Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: OoPEZoO on April 20, 2014, 02:50:11 PM
Quote from: Bman on April 20, 2014, 11:11:36 AM
I don't think we're trying to be smart asses and "talk down" to you, but rather trying to assist and offer advice.
I hope that's how you're taking this info.  :D

Agreed.  I hope it didn't come off like that. I just hate to see a usable bowl (especially one with the performer tabs) go to the scrap pile when it could easily still be in service. All it takes to get those old one touch systems apart is to cut the sweeper shaft on either side of the nut on the bottom of the kettle. After that, the rest should just fall apart with a little wiggling. I know quite a few guys who have fabricated a replacement support bar for the ash bucket. All it takes is a small piece of sheet metal, a grinder, and a bench vice.  In fact, the SS performer I picked up yesterday has a home made support bar on it. It's not pretty, but it's strong, functional, and no one will ever see it

Regardless, glad your performer is still in service
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: Heyjude on April 20, 2014, 03:45:42 PM
If we can figure out if the brass insert that goes into the burner tube is an off the shelf part, we can build our own regulator and tank connectors form less expensive parts.. 8)
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: drtmcd on April 20, 2014, 05:51:35 PM
Yes, the new regulator was easily removed from the hose shown (1/8" male pipe fitting) and the 2 parts from MSC made the connection from the old regulator to the 1/8" pipe. MSC website will show pics of the fittings.

62251038 3/8T X 1/4 NPTF SAE45DEG FEMALE FLARE X M  1  11.2200     $11.22  http://www.mscdirect.com/product/62251038?rItem=62251038
83294785 1/4 NPTF X 1/8 NPTF BRASS REDUCER COUPLING  1  2.7100     $2.71  http://www.mscdirect.com/product/83294785?rItem=83294785

Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: drtmcd on April 20, 2014, 06:35:39 PM
I wish I had a lot of this info 5-6 weeks ago. I would have proceeded differently. I did not remove the bowl until after I bought the One Touch replacement. I then relied on Weber Customer Service for advice and info on available parts. I emailed them detailed pics of my grill and the rusted bar and cotter key.

I thank everyone for the info posted and do not feel anyone is "talking down to me.". I did not find the WKC until AFTER my rebuild was completed. I posted the info on the gas hose problem to possibly help someone out of the pickle I was in. I went to Ace, Lowe's, Home Depot, and 4 other supply stores in Atlanta before I found the parts on the internet. We all act on the info we have at that time. The rest is 20-20 hindsight.

I hope the current Weber Grills have parts that are more rustproof than the bar, flathead bolts, and cotter key on my 98 Performer and that the engineers concern for rusting of parts matches their concern for my expressed intent to allow me to find parts that would allow me to modify or find a hose to connect to my old regulator and 5 lb tank.

Grill covers are not a solution for and do not stop condensation water damage/ oxidation.

Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: f2benny on October 18, 2014, 09:36:56 AM
I bought a  1999 SS today and looking for an answer to this question too.  Mine has OPD QD tank but it's expired though otherwise nice shape.  In the thread, it is mentioned that the 5 lb tank may be refilled from a 20 lb tank which I use on the Genesis (S330).  Can anyone expand on how that would be done if I promise to not complain if I blow up the place?  Thanks
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: Red Kettle Rich on October 18, 2014, 09:46:57 AM
Take heart, whatever is on C/L or ebay will be available again 8)
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: demosthenes9 on October 18, 2014, 09:49:03 AM
Quote from: f2benny on October 18, 2014, 09:36:56 AM
I bought a  1999 SS today and looking for an answer to this question too.  Mine has OPD QD tank but it's expired though otherwise nice shape.  In the thread, it is mentioned that the 5 lb tank may be refilled from a 20 lb tank which I use on the Genesis (S330).  Can anyone expand on how that would be done if I promise to not complain if I blow up the place?  Thanks

Grab one of these.

http://www.amazon.com/Mr-Heater-F276172-Propane-Adapter/dp/B000AMC5WO/ref=sr_1_2?ie=UTF8&qid=1412011496&sr=8-2&keywords=propane&tag=viglink21354-20

Screw one end onto the 5lb tank, then screw the other into your 20lb tank.  Open the valves and away it goes.

Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: f2benny on October 18, 2014, 10:50:00 AM
But I have a QD on my 5 lb tank.  That won't fit I think-right?
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: OGlenn on October 18, 2014, 01:05:23 PM
Yes, you'll need a quick disconnect adapter--that one in the earlier post is used to refill the 1 lb tank, not your 5lber.  I bought a copper line with two male P.O.L. fittings so I could screw one into the 20 lb tank and the other end into the adapter, like this: http://www.ebay.com/itm/Propane-Tank-All-Brass-Cooper-P-O-L-x-P-O-L-x-18-inch-Regulator-Adapter-/111469971161?pt=LH_DefaultDomain_0&hash=item19f420c6d9. I've been lucky that the SS performers I've restored all had the original adapter, but you can still find them fairly easily.

(http://i1330.photobucket.com/albums/w579/O_Glenn/CIMG0218_zps40e0652a.jpg)
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: f2benny on October 18, 2014, 04:35:38 PM
After all that the kid at the propane shop filled it without batting an eye while I chatted to him.   
Title: Re: Questions about those old 5 lb propane tanks on the SS Performers
Post by: Bman on October 18, 2014, 04:59:17 PM
Quote from: f2benny on October 18, 2014, 04:35:38 PM
the propane shop filled it without batting an eye.   

Exactly what I was going to ask - Did you try?
My local lumber yard does this also and if I blow something up, their name will never be mentioned.  It came this way.  lol