Restoring a Cast Iron Dutch Oven Using Electrolysis

I’ve been wanting to restore this old Dutch Oven (somethings referred to as a Camp Dutch Oven because it has feet and a raised-lip lid) for some time. I found it at an antique store in Railroad PA years ago, and it sat in my barn gathering dust and more rust since then. I had heard about this thing called electrolysis a while back, but figured this was too far gone to save. Almost trashed it a couple times during our annual clean-out.  IMG_5991IMG_5993IMG_5994

Now we all know how well cast iron and Weber kettles go together – a perfect match for many dishes, and anyone with a kettle should own at least one oven and a skillet made of iron.

This techinique works extremely well for cast iron grates, too!

I’ve been using my “indoor” dutch oven (a Le Creuset 5 qt) for some time, but the cleanup takes forever – especially if I’m using smoke wood. I really needed an “outdoor” oven; one that I could set directly on the coals without worry. This old rusty 12″ camp dutch oven might just do the trick, but I would have to figure out how to do this thing called electrolysis first. Thanks to the internet, and the hundreds of videos of people using this process to clean up all kinds of rusty old stuff, I thought I would give it a try. I had a plastic tub, a battery charger, and some scrap metal. (Don’t we all?) All I needed to buy was a box of Arm and Hammer Super Washing Soda – set me back $3.50.  IMG_6449 Charger

Setting up the tank couldn’t have been easier. 10 gallons of water from the hose, and 10 tablespoons of washing soda mixed in. An old Smokey Joe grate I had laying around (don’t we all?) served as the anode – it would attract the rust from the oven once I hooked it up to the charger. (I hope…) Submerged the bowl in the tub, hooked the negative clip from the charger to it, (note that the clip is actually under water at this point – seems to work fine like that) and hooked the positive clip to the SJ grate. (keep this one above water if you know what I mean) Plugged it in and waited…  IMG_6471

And waited…

Went to bed…

In the morning, I was anxious to see what happened. I was expecting little progress. After all, this thing was RUSTY! To my amazement, when I lifted it out of the tank, it was nearly rust free! A few minutes with a wire brush and it started to look like new. I was amazed – my wife was amazed. It was amazing!  IMG_6477

The lid went in next – same solution.  IMG_6478 IMG_6481

No need to start with clean water – the process works just the same regardless how grungy the water looks. Fast forward another 12 hours and the lid came out just as clean!  IMG_6510

Started thinking about how to season the oven, and again hit the web for advice. Well, let me tell you there are a thousand opinions about what to do or not to do. After drying it out in a 200 degree oven for 15 minutes or so, I ended up using course salt and a little solid shortening for the first stage – to clean out any remaining grunge and rust. IMG_6485

Wiped it down good and put it in the oven for 20 minutes or so at 350.  IMG_6486

Again another wipe down – this time with Canola oil and salt again, a thorough wipe down and some time on the Genesis grill. (Just to Weberize it a bit.)  IMG_6512

Mission accomplished! I’ll be using the oven often now, and will be on the lookout for more rusty treasures to add to the “outdoor kitchen”.  IMG_6513

Try it yourself. It’s easy, It’s cheap. It’s fun. And it works!

 

Postscript: Here’s the SJ grate after 24 hours in service. Looks like it’s good for another few ovens!  IMG_6511

The oven had a pair of tags on it – likely the owner had used it in group cooks or competitions in the past.  Fun to think about the meals it has seen, and even more fun to think of the meals to come! IMG_6441

And a few tips I learned along the way:

  • DON’T let the thing you are cleaning touch the sides of the tub, or the anode.
  • DON’T hook the positive clip to the thing you are cleaning and the negative to the anode.
  • DO rotate the thing you are cleaning every few hours. The electrolysis action is highest close to the anode, so if you only have one anode, it’s best to expose it to as many sides of the thing you are cleaning for as long as possible.
  • DO set this up outdoors or in an open garage; it creates hydrogen gas as a result of the process, so…
  • DON’T smoke or light a grill close-by. (Oh! The Humanity!)
  • DO collect old rusty iron when you find it, once this is set up you’ll want to keep it running!
  • DON’T believe everything you see on the web about this process. Try it yourself and you’ll get the hang of it quickly.
  • DO post pics of your own restorations here at the WKC, and especially the cooks you do after you’re done.

MartyG – August 2014

 

 

3 comments… add one
  • Weber’s and cast iron do compliment each other. I bake in the Weber kettle with cast iron a lot. Your method does work and it is easy. It is a little scary at first using electricity and water together but the results are worth it. A picture of my Weber kettle and a project I undertook is here.
    http://www.madmeatgenius.com/2012/09/black-iron-dude.html

  • fedex Link Reply

    All my cast iron is in great shape but now I need to find a rusty pos to try this. Great write up and thanks for sharing.

  • Wow, that was great! I need to keep my eyes open for some rusted out cast iron no one wants! Thanks for sharing.

Leave a Comment